







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterCabinet Installation & Refacing in Glendale, CA
Cabinet installation and refacing in Glendale usually runs $4,200 to $9,800 for a standard 10-by-10 kitchen, with full custom installs climbing past $18,000 and refacing landing closer to $3,500 to $7,000. The difference between the two is simple: installation means new boxes, refacing keeps the existing cabinet frames and replaces the doors, drawer fronts, and veneer. We’re Rowan Construction Group Glendale, and we do both under the same written-price discipline that governs every trade we run.
Most Glendale kitchens we walk into were last touched in the 1980s or 1990s. The cabinets are solid wood underneath, but the doors are dated oak with brass pulls, and the layout was built around a 30-inch range that’s since been swapped for a 36-inch. Whether that means refacing the boxes or pulling them entirely depends on the frame condition, and we say which in writing before anyone lifts a screwdriver.
Under Clause 1 of The Haven Standard, you get a flat written price and a written scope before work starts. No “call for a quote.” Call (844) 320-5930 and we’ll schedule the measure. For the full picture of how cabinets fit into a larger renovation, see our kitchen remodeling page and our Kitchen Remodeling in Glendale guide.

Key Takeaways
- Refacing in Glendale runs $3,500 – $7,000; full cabinet installation runs $4,200 – $18,000+ depending on box quality, door style, and whether you’re moving plumbing or electrical.
- Refacing only makes sense when the existing boxes are square, solid, and the layout works. We check all three before quoting.
- Glendale’s 1920s – 1950s housing stock often has non-standard cabinet depths and out-of-plumb walls, which adds labor and sometimes requires custom filler panels.
- Every project gets a documented photo record, a signed change order for any scope change, and the 365-Day Done Right Promise.
- Free second opinion on any written estimate you’ve already received.
When You Need Cabinet Installation & Refacing
The decision usually comes down to frame condition, layout, and how long you plan to stay. Here’s what actually prompts the call:
- The doors are failing but the boxes are fine. Sagging hinges, peeling laminate, swollen MDF around the sink base from years of slow leaks. In Glendale’s older homes, we regularly see sink-base cabinet floors rotted through from a slow drip that went unnoticed for a decade. That’s a refacing candidate if the frame is dry and square, an installation candidate if it isn’t.
- The layout doesn’t work for how you cook. A peninsula blocking the work triangle, a corner lazy Susan that’s never rotated, a refrigerator alcove too shallow for anything built after 2005. Refacing won’t fix a layout problem. New boxes will.
- You’re swapping appliances and the openings don’t match. A 36-inch range replacing a 30-inch, an over-range microwave replacing a hood, a counter-depth fridge replacing a standard-depth unit. Cabinet modification around the opening is often cheaper than a full re-box, and we’ll tell you which in the quote.
- The finish is dated and you’re prepping to sell. Glendale buyers in the $900K – $1.4M range read a kitchen in about nine seconds. Refacing in a current door profile, paired with new hardware and a quartz counter from Cambria or Silestone, moves the room forward without an $18K line item.
- Water damage or pest damage behind the boxes. We’ve pulled cabinets in Glendale and found termite galleries in the studs behind them. Refacing over that is a mistake, and we won’t quote it.
- You want more storage in the same footprint. Full-extension drawers, pull-out trash, a tall pantry cabinet replacing a broom closet. New boxes let you re-engineer the interior; refacing preserves whatever interior you already have.

Our Cabinet Installation & Refacing Process
- Measure and photograph. We measure every wall, check plumb and level at multiple points, and photograph the existing boxes, the substrate behind any damaged panel, and the plumbing and electrical rough-in locations. Those photos go into your file and you get copies. On Glendale homes built before 1960, we also check for knob-and-tube wiring in the wall behind the cabinet run before any box comes down.
- Written scope and flat price. You get a line-item quote: boxes, doors, drawer fronts, hardware, filler panels, crown, toe kick, labor, disposal, and any necessary electrical or plumbing coordination. The number is the number. If something changes mid-job, no work proceeds on the change until you’ve signed a change order.
- Order and stage materials. We source through Wellborn for semi-custom boxes and doors, and we spec countertops from Cambria or Silestone when the project includes them. Lead times run four to eight weeks on most cabinet lines, and we tell you the date up front so you can plan.
- Demo and prep. Old cabinets come out, the wall gets inspected for water damage, pest damage, or out-of-plumb framing, and we correct what we find. Any drywall repair, electrical relocation, or plumbing stub-out happens at this stage, before new boxes go in. We photograph all of it.
- Install and level. Boxes get shimmed, screwed to studs, and leveled across the full run. Doors and drawer fronts get aligned and adjusted. Hardware gets installed to the template you approved. Crown, filler, and toe kick finish the look.
- Walkthrough and photo record. We walk the kitchen with you, confirm every door and drawer operates smoothly, and hand over the documented photo record of what we found and what we did. The 365-Day Done Right Promise applies from that day forward: if something isn’t right, we make it right.
Cabinet Installation & Refacing Pricing in Glendale
Here’s what Glendale homeowners actually pay. These are ranges, not quotes – the written price comes after the measure.
| Scope | Typical Glendale Range | What Drives the Number |
|---|---|---|
| Refacing, standard 10×10 kitchen | $3,500 – $7,000 | Door material, number of doors/drawers, hardware, veneer vs. rigid thermofoil |
| Refacing with new countertops | $6,500 – $12,000 | Counter material (laminate vs. Cambria quartz), edge profile, backsplash |
| Semi-custom installation, standard layout | $8,000 – $14,000 | Box quality, door style, drawer configuration, Wellborn vs. stock line |
| Full custom installation | $14,000 – $22,000+ | Custom sizes, inset doors, integrated appliances, pantry build-outs |
| Layout change (moving sink, range, or fridge) | Add $2,500 – $6,000 | Plumbing relocation, electrical relocation, permit fees, drywall repair |
What pushes the number in Glendale specifically: the housing stock. Kitchens in the 1920s bungalows off Chevy Chase and the 1950s ranches near Adams Square frequently have walls that are out of plumb by half an inch or more over an eight-foot run. That’s not a catastrophe – it’s shim work and custom filler – but it’s real labor, and any quote that doesn’t account for it will come back as a change order. We measure for it up front.
Permits come into play when you’re relocating plumbing or electrical for a layout change. The City of Glendale requires a permit for that work, and we handle the paperwork as part of the project. Cosmetic refacing and like-for-like cabinet swaps generally don’t trigger a permit.
Every quote includes a free second opinion option. If you’ve got a written estimate from another contractor, bring it and we’ll review it line by line at no charge – we’ll tell you what’s missing, what’s padded, and whether the scope matches what you actually asked for. Call (844) 320-5930 to schedule the measure.
Why Refacing Isn’t Always the Cheaper Answer
Refacing gets sold as the budget option, and often it is. But there are three conditions where refacing costs more than it saves. First, if the boxes aren’t square, you’re paying a carpenter to shim and correct before the new doors go on, and that labor erodes the savings. Second, if the interior configuration is wrong – no drawers, deep shelves you can’t reach, a corner with no organizer – refacing locks that layout in for another fifteen years. Third, if there’s any water damage in the sink base, you’re refacing over a problem that will surface again.
We check all three during the measure. If refacing is the right call, we say so and quote it. If it isn’t, we say that too and quote the installation. Either way, the number is in writing before anything starts.
FAQs – Cabinet Installation & Refacing
How much does cabinet refacing cost in Glendale?
Cabinet refacing in Glendale typically costs $3,500 to $7,000 for a standard 10-by-10 kitchen, and $6,500 to $12,000 when new countertops are included. The range depends on door material, the number of doors and drawers, hardware selection, and whether the existing boxes need any repair before the new fronts go on. Call (844) 320-5930 for an exact quote – the measure and estimate are free.
Is it cheaper to reface or replace kitchen cabinets?
Refacing is usually cheaper – roughly 40 to 60 percent less than full replacement – but only when the existing cabinet boxes are solid, square, and the layout already works for you. If the frames are damaged, out of plumb, or the layout needs to change, replacement is the better value because refacing would just lock in problems. We’ll check the boxes during the measure and tell you which makes sense for your Glendale kitchen.
Can you install new cabinets over existing ones?
No, and any contractor who offers to is cutting corners. New cabinet boxes require the old ones to come out so the wall behind can be inspected for water damage, pest damage, and out-of-plumb framing. We photograph that wall after demo and share the images with you. Skipping that step is how hidden rot and termite damage get buried behind a $14,000 installation.
How long does cabinet installation take in Glendale?
Most cabinet installations in Glendale take three to five working days on site, plus four to eight weeks of lead time for the cabinets to arrive after you approve the order. Refacing typically runs two to three days on site with a two-to-four-week lead time on doors and veneer. Layout changes that involve plumbing or electrical relocation add two to four days and require a City of Glendale permit, which we handle.
Do you offer a warranty on cabinet work?
Yes – every cabinet installation and refacing project is covered by the 365-Day Done Right Promise, backed by The Haven Standard. If something isn’t right within a year, we make it right. You also get a written warranty document at project close, alongside the documented photo record of the work performed.
Cabinet work in Glendale is a measure-twice trade. The measure is free, the price is written before anything starts, and the work is documented from demo to walkthrough. Call (844) 320-5930 for a free estimate on cabinet installation or refacing, or to bring us a competitor’s quote for a free second opinion. If you’re weighing cabinets against a broader renovation, start with our kitchen remodeling services overview, or look at how the same written-price process works across our bathroom remodeling projects.
Written by the team at Rowan Construction Group Glendale, serving Glendale.


