







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Driveway & Pavers: The Glendale Owner’s Guide
Replacing a failed Wellborn paver driveway in Glendale typically runs $7,000 to $18,000 installed as a full paver driveway installation, with spot repairs and resealing handled at the lower end of that scale. We’re an independent contractor, not affiliated with Wellborn, and we install and repair Wellborn-compatible hardscape systems across Glendale. The parts that most commonly fail on a Wellborn driveway are not the pavers themselves but the joint sand, the edge restraint, and the bedding layer where water has found a way in.
Glendale owners usually find out the hard way: a paver shifts underfoot after a winter rain, sand washes out along the driveway’s low edge, or a wheel channel starts settling where the car parks every night. Once that happens the piecemeal fixes stop working, and that’s when a proper replacement or re-lay makes more sense than another bag of sand.
Key takeaways
- Wellborn paver failures in Glendale usually trace to joint sand erosion and edge-restraint movement, not the pavers.
- Full installed range here: $7,000 to $18,000 for a paver driveway, with concrete and sealing priced separately.
- Signed change orders control the number; the written price comes before any work starts.
Which Wellborn Models This Applies To

Wellborn’s driveway and paver line spans several product families, and the first job is matching the piece to the driveway you actually have. Most of the paver installations we’re called to in Glendale fall into interlocking concrete paver systems, and Wellborn’s lines are commonly identified by a stamped mark on the underside of each unit or by the shape and thickness (not the top color) of the paver. If you can lift one loose paver from the edge, check the underside for the manufacturer stamp and measure its thickness and footprint – a 60mm paver and an 80mm paver are not interchangeable where vehicle loads are involved.
For proprietary trim, edging, and connector components, a Wellborn part matched to your specific series is the safe route; mis-sizing a base or edge piece shows up as loose pavers within a season. Aftermarket equivalents for standard joint sand, polymeric sand, and edge restraints are widely available and often specified to match or exceed the OEM grade – we’ll tell you which aftermarket pieces are a fair substitute and which ones you should only source Wellborn-branded.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Wellborn Driveway & Pavers Is Failing
- Pavers shifting or rocking underfoot. This means the bedding sand has lost compaction, usually where water is pooling or the base wasn’t thick enough to start.
- Sand washing out of the joints after rain. Joint sand erodes from the low or drainage edge first, and once it’s gone the pavers lose their interlock.
- Settlement in the wheel paths or at the drive apron. Repeated load of the car over a soft spot pushes pavers down and the pattern opens up at the edge.
- Sunken or lifted edge restraint. A failed edge piece lets the whole perimeter creep outward, and that spreads cracks and gaps across the field.
- Wide, wandering cracks or a lip at a control joint. Usually a sign the base or subgrade is moving under load, not a surface problem you can sand away.
Glendale’s climate matters to all of this. The long dry season bakes the sand and hardens the subgrade, then the wet winter months swell the soil and force water under the pavers where the joint sand has thinned. Driveways facing south get the most solar load and dry out fastest; driveways under mature street trees deal with root lift along one edge. That’s why we see the same failures repeat in the same Glendale neighborhoods rather than at random.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a Glendale driveway, plan on $7,000 to $18,000 for a full paver driveway installation. If the base is sound and we’re re-laying or repairing rather than replacing, the number drops toward the low end; a full tear-out with base rebuild and new edge restraint pushes it higher. Concrete driveway installation sits at $4,500 to $12,000, asphalt paving at $3,500 to $9,000, and sealing a paver driveway runs $250 to $700. Paver patio installation, if you’re adding a path or widening the apron, is $3,500 to $11,000.
What drives the range: the base condition (percent of tear-out), driveway square footage, paver thickness and series, edge-restraint and drainage detail, and whether we’re matching into an existing pattern or laying a new one. Every quote is a flat written price with a written scope and warranty before any work begins. No work proceeds on a change until the change order is signed – that’s the discipline that keeps the final number within a few percent of the agreed one. The 365-Day Done Right Promise covers the workmanship: if it’s not right, we make it right.
DIY or Call Us?
You can safely sweep polymetric sand into dry joints and swap a single loose paver after a rain, and pulling up one paver to read the stamp is a fine way to identify your series. What you shouldn’t attempt is resetting a base, rebuilding an edge restraint, or grinding out a settled apron – those are structural fixes where a wrong layer fails you within a season and costs more to redo.
If your paver driveway in Glendale is shifting, pooling water, or losing sand every winter, the base is the question. Bring us a competitor’s quote for a free second opinion, or call us to book an assessment. Every visit includes a documented photo record, so you see exactly what we found under the surface before we touch a thing. Call (844) 320-5930 for a free estimate.
FAQs

Fifteen to twenty-five years is the typical service life for a properly installed paver system with maintained joints, and the pavers themselves often outlast the base by a wide margin. What shortens it in Glendale is failed joint sand, a moving edge restraint, and water intrusion over wet winters. Call (844) 320-5930 for an assessment before a small base problem turns into a full rebuild.
Often, yes. If the issue is localized – a washed-out edge, one settled section, or joint sand that’s simply thinned – a repair and reseal is far cheaper than a full replacement and we’ll tell you plainly when that’s the case. If the base or subgrade is moving, a repair won’t hold and we’ll say so. Call (844) 320-5930 for an exact quote.
Most residential driveway replacements take a handful of working days from teardown through base compaction, laying, and joint sanding, though it stretches for larger driveways or where we’re rebuilding drainage. Weather in the wet season can add time to the base work. Call (844) 320-5930 to get a timeline for your specific driveway.
We match the piece to your existing paver series by reading the stamp on a loose paver and measuring its dimensions and thickness, then specifying the correct joint sand, edge restraint, and base material for that system. For proprietary trim we source Wellborn-branded components; for standard sand and restraints we’ll use quality aftermarket equivalents where they meet or exceed the OEM spec. Call (844) 320-5930 to get a written price.
We also work with KraftMaid, Cambria, and Silestone on the interior trades. Call (844) 320-5930 to schedule your free estimate.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












