







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Techo-Bloc Fence Installation: The Glendale Owner’s Guide
We install Techo-Bloc-compatible fencing and repair failing installations throughout Glendale, and a full fence installation typically runs $3,500 – $9,000 depending on run length, height, and whether footings have to be replaced. Most owners don’t call us because the fence looks bad. They call because a panel is leaning after a Santa Ana wind, a post has settled in the clay-heavy soil up around Chevy Chase Canyon, or a gate swings out of square because the hinge plate pulled loose from the post. That leaning post is the symptom. The cause is usually below grade, in how the footing was set and what it was set into.
We’re an independent contractor, not affiliated with Techo-Bloc, so what you get from us is an honest read on the product and a written price before anything is dug.
Which Techo-Bloc Models This Applies To

Techo-Bloc makes the wall block and retaining systems that anchor most of the decorative fencing installed in Glendale, and the product line matters because the block profile dictates how a post or panel bracket attaches. Their retaining-wall block families are measured in nominal face dimensions, and the ones we see most often on fence work here are the modular lines built around a 6-inch and 8-inch depth with a textured face. The exact series name is usually stamped on the block or printed on the pallet label the installer left behind. Look for that label before you buy anything.
Here’s the compatibility gotcha most homeowners miss: two blocks with the same face dimensions can have different core depth and different pin or clip geometry, which means a bracket that fits one series won’t seat on the other. We measure the block’s actual depth and the pin spacing before we specify a replacement, and we cross-check it against the manufacturer’s current spec sheet. On aftermarket versus OEM: genuine Techo-Bloc parts carry the exact dimensional match and the warranty, while aftermarket equivalents can work when the depth and pin geometry line up and are usually a fraction of the cost. We’ll tell you which route your fence actually needs and put both numbers in the written quote. We also work with KraftMaid, Cambria, and Silestone on the interior and hardscape side, so the sourcing relationships are already in place.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Techo-Bloc Fence Installation Is Failing
Fence problems announce themselves slowly and then all at once, usually in the first strong wind after the rainy season. Here’s what to watch for and what each sign actually means:
- A post leaning toward the street or yard. The footing has lost its grip on the soil or was set too shallow for the load. Glendale’s shrink-swell clay moves through the wet-dry cycle and pulls against a shallow footing until it gives.
- A gate that drags or won’t latch flush. The hinge post has rotated slightly, which throws the whole frame out of square. It’s rarely just a loose screw; tightening it usually buys a few weeks before it goes again.
- Cracks or chips along the block face. Water has gotten behind the wall or into a cold joint and frozen-expanded or washed out the base. Chipping at the bottom course is the tell that drainage was never handled.
- A panel that racks or feels loose when you push it. The bracket or clip that ties the panel to the post has worked loose, or the wrong series part was used and never seated fully.
- Efflorescence or rust streaks. Mineral staining means moisture is moving through the block, and rust means a metal fastener has started to corrode. Neither fixes itself with time; both point to a water path that needs correcting.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Fence installation and repair in Glendale runs $3,500 – $9,000, and we write the price before any work starts. What moves the number: total linear feet of the run, fence height, number of gates, whether existing footings can be reused or have to be dug out and re-poured, and the block profile you’re matching. Repair-only work, like replacing a failed post or re-seating panels, sits at the lower end.
The quote is line-itemed, so you can see the parts, the labor, the footing work, and the disposal as separate lines rather than one lump. Under Clause 1 of the Haven Standard, no work proceeds on a change until the change order is signed, which is why our projects finish within a few percent of the number you agreed to. Every install carries our written workmanship warranty and the 365-Day Done Right Promise: if it isn’t right, we make it right.
DIY or Call Us?
You can safely check a few things yourself. Confirm the block series from the pallet label, measure the actual block depth and pin spacing, and note which posts are leaning versus which panels are loose. Those details help a lot when you call.
What we don’t recommend doing yourself is pulling a footing and re-pouring it, or pulling a post under load. A Techo-Bloc post that’s holding up a full panel run can shift suddenly once the footing is cut, and a heavy block wall coming down out of control is how people get hurt. Digging out a settled footing by hand in Glendale’s clay is also a job that takes far longer than it looks. Call (844) 320-5930 and we’ll tell you honestly whether yours needs a full re-set or just a repair. The estimate is free, and there’s no pressure to book anything.
FAQs

A properly footed Techo-Bloc fence should hold 20 to 30 years, but in Glendale the footing is the weak link, not the block. The material itself handles the sun and dry summers fine; it’s the wet-dry soil movement through the rainy season that shortens life on a shallow footing. Call (844) 320-5930 for a free look at your footing depth.
Yes, often. A single failed post, a racked panel, or a gate that won’t latch can usually be repaired without touching the rest of the run, and that’s the cheaper path when the other footings are sound. We’ll tell you which of the two you actually need after we’ve checked the base. Call (844) 320-5930 for a free estimate.
A single post or panel repair is usually a one-day job; a full fence run typically takes several days depending on length and footing work. We schedule it around weather and give you a written timeline with the quote. Call (844) 320-5930 to get your date.
We start from the block label and the actual measured dimensions, then match your series against the manufacturer’s current spec sheet before specifying a part. Genuine or quality aftermarket, the choice is honest and the number is in writing. Call (844) 320-5930 and we’ll walk through it with you.
Call Rowan Construction Group Glendale at (844) 320-5930 to schedule your free estimate. We’ll come out, check the base and the block series, and hand you a written price with a scoped-out line item for every part and every hour of labor. Our technicians have up to 19 years of experience, every crew is background-checked and uniformed, and every visit comes with a documented photo record so you can see exactly what we found and what we did.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












