







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling: The Glendale Owner’s Guide
Schluter kitchen remodeling in Glendale typically runs $14,000 to $45,000 for a full kitchen, and small kitchens run $9,000 to $20,000. Schluter doesn’t make a part you replace in a kitchen the way you swap a faucet cartridge. What fails in a Schluter kitchen is the waterproofing layer under the tile: a Kerdi membrane seam, a Kerdi-Board joint, or a Ditra mat that lifted after a slab crack or a slow leak behind the range. This guide is written for the Glendale homeowner who already has Schluter in the wall or floor and needs it done right the second time.
Most Glendale owners find out something is wrong when a tile in the backsplash sounds hollow under a knuckle, a grout line near the sink keeps darkening no matter how often it’s sealed, or a soft spot shows up where the counter meets the backsplash. Those are not cosmetic. In a Schluter system, they usually mean moisture has reached the substrate past a compromised membrane seam.
Key Takeaways
- Full Glendale Schluter kitchen remodels run $14,000 to $45,000; small kitchens $9,000 to $20,000.
- Schluter failures are almost always waterproofing failures, not tile failures.
- We’re an independent contractor, not affiliated with Schluter, and we quote a flat written price before work starts.
- Every visit includes a documented photo record of the substrate and the new membrane.
Which Schluter Models This Applies To

Schluter’s kitchen line breaks into three families, and identifying which one you have tells us what failed. Kerdi is the sheet-applied waterproofing membrane for showers and walls, including backsplashes when a homeowner wants full waterproofing behind tile. Kerdi-Board is the foam building panel with Kerdi already laminated to it, used for walls and backsplash runs. Ditra and Ditra-Heat are the uncoupling mats under floor tile, with Ditra-Heat adding an embedded electric heating cable.
To identify yours, look at the exposed edge behind the range or under the dishwasher. Kerdi membrane is a thin orange fleece-backed sheet. Kerdi-Board is a foam panel with orange facing, usually 1/2 inch or 3/4 inch thick. Ditra shows as an orange mat with a dovetail grid pattern on the underside. If the kitchen is older and you see a gray or green board instead, the waterproofing was never Schluter to begin with, and the failure points to a different problem.
The OEM-versus-aftermarket question doesn’t apply to Schluter the way it does to a cabinet hinge. Schluter’s own Kerdi-Band, Kerdi-Fix sealant, and preformed corners are what we specify because the membrane warranty hinges on using the matching system. Aftermarket waterproofing sheets exist, they cost less per square foot, and mixing them with Schluter panels voids the assembly warranty. We don’t stock parts or carry them on a truck; we source what the job calls for and show you the product before it goes on the wall.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling Is Failing
- Hollow tile sound along a seam. A dull thud instead of a sharp tap means the thin-set under the membrane released, usually after a slab or stud movement. In Glendale, we see this most on older homes near Brand Boulevard where the original framing is 1940s.
- Grout lines that darken and stay dark. Grout is vapor-permeable. If a line stays dark after drying, moisture is traveling behind it through a failed Kerdi-Band seam and isn’t escaping.
- Lifted or tented Ditra mat. A mat that has separated from the subfloor in a floor area shows as a soft spot or a slight ridge. Underfoot, it flexes. This is common over slabs that crack in the heat.
- Rust or corrosion at the base of metal appliances or trim near the backsplash. Water has been sitting at the wall-floor junction for weeks. This is the clearest evidence of a waterproofing breach.
- A musty smell near the sink cabinet, under the dishwasher, or around a wall oven. Not a spill. It points to moisture trapped in the substrate behind the membrane, and it’s the symptom that turns a $3,000 repair into a $14,000 remodel if left alone.
Two facts matter here. California’s dry climate does a good job of drying a membrane breach in summer, which masks the problem until winter rains move in and the seam opens further. And Schluter’s published membrane system is rated to perform for the life of the assembly, not a fixed number of years, which means a failure inside 15 years is a workmanship or design question, not a materials question.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Glendale, a full Schluter kitchen remodel with new waterproofing runs $14,000 to $45,000. The lower end is a small galley kitchen with a backsplash-only membrane repair and new tile. The upper end is a full kitchen with new cabinetry, countertops, and floor Ditra-Heat with new cable. A standalone membrane-and-tile repair at the backsplash runs $800 to $2,500, and a floor Ditra repair runs higher if the mat has to come out and reform over the slab. These are the numbers we quote, not starting-at numbers.
What drives the range on your Glendale kitchen:
- Square footage of membrane and floor area to be redone.
- Whether the case has to come apart (cabinet removal adds labor).
- Whether the subfloor or slab is cracked and needs a membrane-specific crack-isolation layer.
- Tile selection: natural stone weighs more and needs a thicker membrane assembly than porcelain.
Every Rowan kitchen quote is a flat written price with a written scope and written warranty. No work proceeds on a change until the change order is signed. The install itself is covered by our 365-Day Done Right Promise: if it isn’t done right, we make it right. We’re not affiliated with Schluter, and we’ll say so on the quote.
DIY or Call Us?
What a Glendale owner can safely check without tools: tap along the backsplash with a knuckle and note where it sounds hollow, look for rust at the base of metal appliances near the backsplash, check the grout line behind the sink each month, look at the edge of the Ditra mat under the front of the dishwasher or under the floor near the range. Those four checks tell you whether to call us.
What an owner should not attempt: removing tile to inspect the membrane, patching a Kerdi-Band seam, or re-setting a lifted Ditra mat. The failure isn’t the tile. It’s underneath, and the fix requires cutting back to a clean substrate, re-flashing to Schluter’s spec, and matching the Kerdi-Fix sealant cure time. Getting it wrong leaves a failure that shows up 18 months later. Call (844) 320-5930 and we’ll take a look and tell you the honest answer.
FAQs

Schluter’s published assembly is rated to perform for the life of the tile installation, and real-world performance in Southern California runs 20-plus years when installed to spec. Failures inside that window point to installation or to a substrate crack that wasn’t isolated. Call (844) 320-5930 for a free estimate to check yours.
Yes, if the failure is localized. A seam that’s open at one joint can be cut back, re-flashed, and re-tiled for $800 to $2,500 in Glendale. Once moisture has spread to the substrate, we’re looking at a larger tear-out. That range is what we quote in writing, and we’ll tell you which case you’re in after we look.
A backsplash membrane-and-tile repair typically takes two to three days in a Glendale kitchen: one day demo and substrate prep, one day membrane and sealant cure, one day tile and grout. A full kitchen remodel with floor and wall membrane is two to three weeks. We’ll put the schedule in writing before we start.
We match the material to the assembly you have, then show you the product before it goes on the wall. Kerdi, Kerdi-Board, Kerdi-Band, Kerdi-Fix, Ditra, and Ditra-Heat are sourced to the exact panel or mat thickness your substrate requires. We don’t stock parts and don’t carry them on a truck: the right membrane for a 1940s Glendale bungalow over original framing is often different from what a 2000s rebuild uses. Call (844) 320-5930 for a free estimate.
If you’ve already been quoted a Schluter repair by another contractor in Glendale, bring us the written estimate. We offer a free second opinion, reviewed line by line at no charge, and we’ll tell you if the scope misses the underlying failure. We also service KraftMaid, Cambria, and Silestone kitchens alongside Schluter assemblies, so a single quote can cover the cabinet and countertop work if your remodel is already in motion.
Call (844) 320-5930 to schedule your free estimate on Schluter kitchen remodeling in Glendale. Our technicians have up to 19 years of experience, every crew member is background-checked and uniformed, and a live person answers the line 24/7. You’ll get a written price before any work starts, a signed change order before any change proceeds, and a documented photo record of the substrate and the new membrane when we leave.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












