







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Glendale Owner’s Guide
We build home additions and ADUs in Glendale using Schluter waterproofing and substrate systems throughout the wet areas – DITRA and KERDI under baths and laundry floors, KERDI-BOARD in shower surrounds and utility walls, KERDI-LINE drains where a linear drain makes sense. A full addition in Glendale typically runs $45,000 – $130,000 installed, a garage conversion $30,000 – $80,000, and a detached ADU $90,000 – $220,000. A written flat price comes before anyone picks up a tool.
Owners usually find out something is wrong with the Schluter assembly after the fact, not during the pour. It shows up as a soft spot or hollow thud underfoot in the new bath, grout that darkens in one line and stays dark, tile that pops free along a shower curb, or a faint musty smell in an ADU bathroom that doesn’t come from the sink. We’re Rowan Construction Group Glendale, an independent contractor and not affiliated with Schluter, and the call we get most often from Glendale is about water that got under a membrane that was never seam-taped correctly, or a substrate that flexed past the manufacturer’s deflection spec on a second-story addition built over an older first floor.
Key Takeaways
- Most Schluter failures in Glendale come from installation, not the membrane itself – unbanded seams, missed inside corners, or a subfloor that flexes beyond spec.
- You can’t judge a Schluter installation by looking at the tile. Waterproofing is buried, so the diagnosis starts with the substrate and the paper trail.
- Addition and ADU pricing in Glendale starts at $45,000 for an addition and $90,000 for a detached ADU, quoted flat and in writing before work begins.
- We source Schluter systems through vetted distributors and match the exact profile, drain, and board thickness to your build.
- Every visit includes a documented photo record of what we found and what we did, whether that’s a moisture reading or the condition of a finished floor.
Which Schluter Systems and Parts Apply Here

Schluter isn’t a single product – it’s a family of assemblies, and the “part” you need depends on which one is under your tile. The main lines in an addition or ADU are:
- DITRA and DITRA-HEAT – the uncoupling membrane, sold in rolls and mats. The relevant spec is thickness (DITRA is about 1/8 inch, or 3 mm; DITRA-XL is 5/16 inch), and rolls come in 3’3″ widths in standard, XL, and larger formats. The newer DITRA-PLUS rolls run in wider master-roll formats. Measuring your roll’s printed edge label is the surest way to match.
- KERDI and KERDI-BAND – the waterproofing sheet and the seam band. KERDI-BAND comes in 5″ and 7″ widths and 10-meter or 30-meter rolls. Getting the right width matters: 5″ is fine for floor-to-wall inside corners, 7″ is what we reach for on curb wraps and wider overlaps.
- KERDI-BOARD – the waterproof backer board, made in thicknesses from 1/4″ up through 2″. The half-inch is standard on shower walls; the thinner 1/4″ is for floor underlayment. Board thickness is printed on the edge and is the first thing to check.
- KERDI-LINE and KERDI-DRAIN – linear and point drains. The drain flange size and the grate frame you’re matching is the compatibility gotcha here: KERDI-LINE comes in multiple grate frame lengths, and a grate that came with one frame won’t seat in another.
- SCHIENE, DILEX, and JOLLY – the edge and movement profiles. These are the ones owners most often break, and they’re the least expensive to replace.
OEM versus aftermarket for Schluter is a different question than it is for a washing machine. Schluter sets the system warranty, and mixing an aftermarket membrane with Schluter’s own band and corner pieces can void the system coverage. When an owner’s failed part is the membrane or a drain, our advice is to stay within the Schluter system for that assembly rather than substitute.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
Tile hides almost everything, so the symptoms come late. These are the ones we’re called about most in Glendale:
- Hollow sound and loose tile over a wet area. Tap a few tiles with a plastic-handle screwdriver. A hollow tone over a bath or laundry floor usually means the uncoupling membrane has debonded; the cause is nearly always a subfloor that flexed past spec on a second-story addition, or thinset that skinned over before the tile went down.
- A dark grout line along the shower curb or floor edge. Grout that stays darker than its neighbors means moisture is wicking in through a seam that was never banded properly or a corner profile left out. It won’t dry because it can’t escape.
- Tile popping free at the shower pan transition. When the KERDI-DRAIN faucet or linear drain flange isn’t bedded tight, the movement at the drain edge cracks the tile over it. This is a drain issue, not a tile issue, and it will return if only the tile is reset.
- A creeping musty smell in a new ADU bathroom. If the smell doesn’t clear after cleaning and doesn’t come from the sink, it’s typically trapped water under a membrane that was installed without proper overlap. By the time you smell it, the board behind is wet.
- Efflorescence – white powder – at the base of an exterior tile wall. Powder means water is moving through and evaporating there. On an addition exterior facing the Glendale sun and the occasional marine-layer morning dampness, this often traces to a missed weep or a substrate that wasn’t sealed at the edge.
Here’s the honest part about the two you can’t check yourself. A failed Schluter assembly is not a part you swap out of a hatch; the membrane and the drain are buried under tile and thinset, and getting to them is demolition. That’s not an overstatement to scare up business – it’s the practical reality. If you suspect the pan is wet, stop using the fixture and get a moisture reading rather than a guess.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Because the “part” lives under the finish, the quote is an elapsed-cost question, not a parts-counter question. Here are the Glendale ranges we work to:
| Scope | Glendale range |
|---|---|
| Home addition (full, framed to finish) | $45,000 – $130,000 |
| Garage conversion | $30,000 – $80,000 |
| ADU construction (detached) | $90,000 – $220,000 |
| Wet-area substrate and membrane rebuild, per bath | Quoted line-item within a bath remodel ($9,000 – $28,000) |
The range swings on size, foundation and grading, whether the footprint triggers a setback or hillside review, and the number of wet areas. What’s included in every written quote: the Schluter system specified by name and thickness, the drain and grate included, a written scope, and the warranty on the work. The quote is a flat number, not a “call for a quote” placeholder. Under Clause 1 of The Haven Standard, the price is in writing before anyone starts – and no change happens until you sign a change order. Our technicians have up to 19 years of experience.
DIY or Call Us?
What you can safely check yourself: the age and label on any leftover Schluter materials, whether your grout darkens in one line, and whether a floor sounds hollow. What you can’t do yourself is resolve a buried membrane failure. Removing a shower pan or cutting into an addition floor is demolition and, in a wet-area rebuild, water and electrical may be in the same assembly. That’s work for trained professionals with a moisture meter and a plan.
We can also read a competitor’s written estimate line by line at no charge – our free second opinion – and tell you whether the membrane and drain were actually priced in. Call (844) 320-5930 to schedule your free estimate.
FAQs

Installed correctly, a Schluter DITRA or KERDI assembly is expected to last the life of the tile above it – decades. In practice, lifespan hinges on the substrate. A floor that flexes past the manufacturer’s deflection spec will fail a correctly installed membrane, and Glendale’s older homes with remodeled second stories are where we most often see that. Call (844) 320-5930 for a reading and a flat written price.
Sometimes. A cracked edge profile like SCHIENE or JOLLY can be swapped without touching the waterproofing. A failed seam band or a stuck KERDI-LINE grate can sometimes be corrected locally. A failed drain flange or a debonded pan usually means rebuild, because the failure lives under the tile. Call (844) 320-5930 and we’ll tell you which side of that line your project is on – the estimate is free.
A profile replacement is a one-visit job. A shower pan or bath membrane rebuild in a Glendale addition typically takes several working days once demolition starts, because the board has to dry, be rebanded and allow curing before tile goes back. A garage conversion or ADU is a multi-week build and we schedule it as a written plan. Call (844) 320-5930 for a written schedule with your price.
We source Schluter systems through vetted distributors, matching the exact profile, thickness, drain flange, and grate frame to what’s already in your build. We don’t stock parts and we don’t carry them on a truck – the match is verified against the job before anything ships. We also work KraftMaid, Cambria, and Silestone where the scope calls for them. Call (844) 320-5930 to start with a written price.
Whether your addition needs a fresh Schluter assembly from the slab up or a failed pan rebuilt in a Glendale bath, the next step is the same: a written price before work starts, a signed change order before any change, and a photo record when the crew leaves. Call Rowan Construction Group Glendale at (844) 320-5930 to schedule your free estimate – and if you already have a quote from someone else, bring it and we’ll go through it line by line at no charge.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












