







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Glendale Owner’s Guide
KraftMaid fence installation in Glendale typically runs $3,500 – $9,000 installed, and that figure covers removing the failed section, setting posts to California code depth, and hanging the new fence with a written warranty. We’re an independent contractor, not affiliated with KraftMaid, and we install to the brand’s published specs rather than substituting parts that almost fit. Most Glendale owners first notice something is wrong when a gate stops latching cleanly or a panel leans after a Santa Ana wind event.
Key takeaways:
- KraftMaid fence systems are spec-driven. Post spacing, panel height, and picket profile all have tolerances that a generic hardware-store substitute won’t meet.
- A fence that leans in Glendale is usually telling you about soil, not the fence. The Verdugo foothills get shrink-swell clay that moves a post faster than any picket weathering.
- Full-fence KraftMaid installation runs $3,500 – $9,000. A single section repair is a different job and often a fraction of that.
Which KraftMaid Models This Applies To

KraftMaid’s fence lines are identified by the series name stamped on the gate hardware plate or printed on the label inside the top rail cap. Look there first. If the label is gone, measure the picket width and thickness with calipers and compare against the three KraftMaid picket profiles: the standard 5/8-inch, the heavier 3/4-inch, and the arched-top profile that appears only in certain decorative series. Each profile mates with specific top-rail channels, and a top rail made for a 5/8-inch picket will not hold a 3/4-inch picket without visible slop.
This is where the OEM-versus-aftermarket decision gets real. An aftermarket picket from a big-box store will physically fit the rail channel on many KraftMaid systems, but the color hold and the profile radius won’t match, and in five years the mismatch will show on a south-facing fence in Glendale’s sun. For a single picket replacement, aftermarket is fine. For sections visible from the street, OEM or a matchup from a manufacturer that publishes its color formulas is the honest call. We source KraftMaid-compatible components through our vetted supplier network, and the same network supplies our Cambria, Silestone, and Kohler work. Every quote lists the exact part number and series on the line item.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Fence Installation Is Failing
- Posts leaning after a rain. In Glendale’s clay, a post set in a concrete footing too shallow to reach stable subsoil will rock as the clay swells. The fence isn’t failing; the footing is. We see this most in the older blocks near Adams Square.
- Gate sag and chronic latch miss. Gate hardware takes all the load in a fence system, and a worn hinge or a hinge screw that’s lost bite is the usual cause. A gate that needs lifting to latch is a hardware failure, not a frame failure.
- Surface checking and gray-out on pickets. Weathering wood or vinyl that’s gone chalky means the finish is gone. On a KraftMaid vinyl or composite system, chalky pickets that won’t clean back to color are past refinishing.
- Loose or missing fasteners along the top rail. Wind cycling works fasteners out of the rail channel. If you can pry the top rail and see daylight between rail and picket, the fasteners have backed out.
- Rot at the post base. The post base is where water pools. Soft wood or a hollow sound when you tap the base means the post is compromised and the panel is no longer structurally held.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Fence installation in Glendale runs $3,500 – $9,000 for a typical residential run, and the range moves with linear footage, height, and how much existing fence has to come out. What drives the number is mostly earthwork: in parts of Glendale, a post hole hits rock within a foot and the footing has to be pinned instead of simply dug. That’s a line item on the quote, not a surprise.
| Line item | Typical range |
|---|---|
| Removal and haul-away of existing fence | $300 – $800 |
| Post setting and footings (per post) | $75 – $200 |
| KraftMaid-compatible panels and pickets | $40 – $110 per linear foot |
| Gate hardware and hanging | $150 – $450 |
| Total installed, typical residential run | $3,500 – $9,000 |
Every Rowan quote is a flat written price with the parts, labor, and warranty spelled out before anyone starts. Under Clause 1 of The Haven Standard, the number goes on paper first, and no change proceeds without a signed change order. That’s the discipline keeping 4,000-plus projects within a few percent of the agreed cost.
DIY or Call Us?
You can safely check a few things yourself. Walk the line and look for lean. Tap the post bases. Pry the top rail gently to feel for slack fasteners. Read the label inside the rail cap and write down the series and profile. Those five minutes tell you whether you have a hardware problem or a footing problem.
Here’s where DIY goes sideways. Post footings in Glendale clay require depth and mix that a bag of quick-set and a rented auger won’t reliably deliver, and a post that fails in two years takes the whole panel with it. Fence work also sits close to property lines, and Glendale has setback and height rules that vary by zone. Get it wrong and you’re pulling a fence you just built. A licensed contractor carries the liability for the footing and the code compliance; that’s most of what you’re paying for. Call (844) 320-5930 and we’ll tell you honestly whether you need a full run or a repair.
FAQs

A well-installed KraftMaid fence in Glendale will typically give you 20 to 30 years on the structure, with the finish needing attention sooner. The variable in Glendale isn’t the fence; it’s the soil and the sun. Clay movement stresses the footings, and the UV load on a south-facing run is higher than the manufacturer’s baseline. That’s why we photograph the footings before we backfill.
Often, yes. A single leaning post, worn gate hardware, or a cracked picket is a repair, and you shouldn’t be sold a full replacement for it. A run with three or more failed sections or soft post bases is usually a replacement. We’ll tell you which one yours is, in writing, with photos.
A typical residential KraftMaid fence run in Glendale takes two to four days, and rock in the dig is the main thing that pushes it longer. We don’t quote a start-to-finish window we can’t hold. You get the schedule and the daily photo record.
We match your series and picket profile through our vetted supplier network and list the exact part number on the line item of the quote. That network also feeds our Cambria, Silestone, and Kohler work, so the sourcing discipline is the same across trades. If the exact part isn’t available, we tell you what we’re substituting and why, before you sign.
Ready for a number in writing? Call (844) 320-5930 for a free estimate on KraftMaid fence installation in Glendale. Bring a competitor’s quote and we’ll review it line by line at no charge.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












