







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Kitchen Remodeling: The Glendale Owner’s Guide
We install and remodel Kohler-equipped kitchens in Glendale, and the installed price for a full Kohler-spec kitchen remodel here runs $14,000 – $45,000 depending on cabinet layout, countertop material, and whether the plumbing and electrical get moved. If a Kohler component in your kitchen has failed or is failing, the first sign is usually a faucet that drips at the base after you shut it off, a pull-down spray head that won’t stay seated, or a sink strainer that no longer seals against standing water. Kohler fixtures hold up well, but every cartridge, aerator, and spray diverter has a service life, and in Glendale’s hard water those parts tell you when they’re done.
We’re an independent construction contractor, not affiliated with Kohler. What we do is install Kohler products, source the correct replacement parts for them, and stand behind the installation in writing.
Key Takeaways
- A full Kohler kitchen remodel in Glendale: $14,000 – $45,000 installed.
- Small kitchen remodel scoped around Kohler fixtures: $9,000 – $20,000.
- Cabinet installation alone: $4,000 – $13,000. Countertops: $2,000 – $6,500.
- Every job gets a flat written price before work starts, and no change proceeds without a signed change order.
- Our technicians have up to 19 years of experience with Kohler and comparable fixture lines.
Which Kohler Models This Applies To

Kohler’s kitchen faucet lineup splits into a few families that matter for parts: the Artifex and Bellera pull-downs, the Cruette and Graze semiprofessional styles, and the Simplice and Malleco workhorse models. Cartridge and valve compatibility is not universal across these. A cartridge pulled from a Simplice will not seat correctly in a Cruette body even though the handles look similar. That’s the most common compatibility mistake we see in Glendale kitchens, usually after a homeowner bought a part online by photo.
Find your model number before ordering anything. Kohler stamps it on the underside of the faucet base, on the escutcheon ring, or inside the cabinet on the supply-line tag. If you can’t find it, measure the spout reach and the base diameter and photograph the handle assembly. Those three data points narrow the model family quickly.
On the OEM-versus-aftermarket question: for Kohler, we lean OEM on cartridges, ceramic valves, and spray diverters. The aftermarket equivalents we’ve seen in Glendale run a few dollars cheaper but use a different ceramic disc composition that wears faster in our water. For cosmetic parts like aerators and O-rings, quality aftermarket is fine.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Kohler Kitchen Remodeling Is Failing
- The faucet drips at the spout after shutoff. That’s a worn ceramic cartridge, and in Glendale’s water it happens faster than Kohler’s general spec suggests because mineral deposits score the disc faces. Left alone, the drip becomes a steady stream within months.
- The handle feels gritty or stiff to turn. Sediment has worked into the valve body. The cartridge is still functional but the stem is being abraded every time you use it, which shortens its life.
- The pull-down spray head drips or won’t hold its position. The diverter or the magnetic docking ring has failed. This is a common failure on Artifex and Bellera models after several years of daily use.
- Water pools at the base of the faucet on the countertop. The base O-ring or the mounting gasket has degraded. Water tracking under the fixture can damage the countertop substrate if it goes unaddressed.
- The sink strainer won’t hold water or drains slowly. The rubber seal has hardened, or the basket assembly has corroded. Cheap part, real annoyance, easy to fix correctly.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Kohler-spec kitchen work costs in Glendale, installed, with parts and labor shown together so you can compare apples to apples:
| Scope | Installed Price (Glendale) |
|---|---|
| Full kitchen remodel (Kohler fixtures throughout) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range: cabinet box construction and door style, countertop material and edge profile, whether the sink and faucet location moves (which means plumbing rough-in), and whether the electrical needs upgrading to support a Kohler induction or smart appliance. A countertop swap on existing cabinets sits at the low end. A full gut with new layout sits at the top.
Under Clause 1 of The Haven Standard, you get a flat written price with a written scope before anyone touches the kitchen. If a Kohler part we didn’t anticipate turns up worn during demo, we write a change order, you sign it, then we proceed. Nothing moves without your signature. Every job carries the 365-Day Done Right Promise, and every visit includes a documented photo record.
DIY or Call Us?
An owner can safely check a few things: shut off the supply valves under the sink, confirm the model number, inspect the aerator screen for grit, and tighten a loose handle screw with an Allen key. That’s the ceiling for safe DIY. Replacing a Kohler cartridge requires shutting off the supply, disassembling the valve body, and reseating a new cartridge without scoring the ceramic disc, and a wrong move there means a leak inside the wall or under the counter. Kitchen plumbing and any electrical work behind the wall is not a DIY zone. We’d rather you call us than find water damage three weeks later.
If you’re mid-remodel and weighing a kitchen project around Kohler fixtures, we’ll put a number in writing before anyone picks up a tool. We also work with KraftMaid and Cambria, and we’ll happily source Silestone countertops if that’s what fits your plan. Call (844) 320-5930 for a free estimate, and we’ll schedule a walkthrough at your kitchen.
FAQs

Expect 5 to 8 years on a Kohler ceramic cartridge in Glendale, shorter if your water runs hard or the faucet sees heavy daily use.
Often, yes. A dripping cartridge can usually be swapped without replacing the whole faucet, and a worn spray head or strainer is a straight part replacement. We assess on-site and tell you which option costs less over time.
A faucet cartridge or spray-head replacement takes about an hour. A full faucet swap runs 1 to 2 hours. A kitchen remodel scoped around Kohler fixtures is a multi-day job, and we give you a written schedule with the quote.
We match the part to your faucet’s model number and series, sourced from Kohler or a vetted supplier. Once the part is confirmed, we send you a written price and a photo of what we found before we install.
Call (844) 320-5930 for a free estimate. We answer with a live person, and we’ll confirm your appointment by text.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












