A Rowan company - serving Glendale, CA
A backyard with a new horizontal privacy fence
Jerith · Glendale

Jerith Fence Installation in Glendale, CA

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Glendale
A new black aluminum pool fence with a gate
A new wood side gate with black hardware
A finished backyard cottage with a small covered porch
A new roof with clean valleys and new flashing
A new multi-panel patio door opening a kitchen to the patio
A new paver patio with a seat wall and fire pit
A remodeled primary bathroom with a soaking tub and walk-in shower
A single-story rear room addition with tall windows and a new patio
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Jerith Fence Installation: The Glendale Owner’s Guide

Fence installation with Jerith-compatible materials in Glendale typically runs $3,500 to $9,000 installed, with ornamental aluminum and vinyl projects landing in that range depending on linear footage, gate count, and site conditions. We’re an independent contractor, not affiliated with Jerith, and every job starts with a written flat price before anyone picks up a tool. Most Glendale owners find us after a section has failed – a gate that sags, a post that leans, or panels that have started to chalk and warp after a few summers of San Fernando Valley heat.

Call (844) 320-5930

Key Takeaways

  • Installed Jerith-compatible fence work in Glendale: $3,500 to $9,000.
  • Written flat price before work begins, on every project.
  • 365-Day Done Right Promise on every install.
  • Free Second Opinion on any written estimate you’ve already received.

Which Jerith Models This Applies To

A new stained cedar privacy fence

Jerith Manufacturing builds ornamental aluminum fencing across several residential lines – the Estate and Traditional grades being the most common in Glendale backyards, with the heavier commercial-grade pickets showing up on corner-lot frontages and hillside properties in Chevy Chase and the Verdugo Woodlands. Identifying the right match starts with the label inside the post cap or stamped on the bottom rail; if that’s faded or gone, measure picket spacing (common residential is 3-7/8 inches on center, 4 inches on the Estate) and post face width.

Original parts through Jerith are the safest match for color and profile, but aftermarket aluminum components in matching powder-coat are widely available and can save real money on a repair where the picket profile has been standardized. The catch: cheap aftermarket caps and brackets often use thinner gauge aluminum and a one-coat finish. In Glendale, where UV exposure is high and the marine layer off the coast can push salt-laden air inland, that single-coat finish will chalk and fade faster than the two-coat premium product. If you’re matching to racks specifically, bring a measurement and we’ll price both paths in writing.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Jerith Fence Installation Is Failing

  • Sagging gates. Usually a hinge that’s wallowed out of the post or a post footing that’s settled. Glendale’s expansive clay soils shift seasonally, and a shallow footing will show it within a few years.
  • Leaning posts. Almost always a footing problem – undersized concrete, no gravel drainage, or a post set into soil that’s been irrigated too heavily along the property line.
  • Loose or rattling pickets. Fasteners work loose from thermal cycling. Aluminum expands and contracts more than people expect across a 40-degree daily swing.
  • Chalky finish or fading. A one-coat powder finish breaking down under UV. Common on aftermarket replacements, rarer on the original Jerith paint system.
  • Rust at cut ends or welds. Untreated cuts from a previous install where the aluminum wasn’t cold-galvanized or capped after trimming.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed fence work in Glendale runs $3,500 to $9,000 for typical residential linear footage. What moves the number: total footage, number of gates, whether old fence and footings need removal, slope or retaining along the run, and whether we’re matching existing Jerith color and profile or replacing a whole section. Every quote is a flat written price with the scope spelled out line by line – materials, labor, haul-away, footings – so there’s no “call for a quote” and no surprise change order. If the job scope changes mid-project, no work proceeds on the change until the change order is signed. The 365-Day Done Right Promise covers the installation, and every visit ends with a documented photo record of what we found and what we did.

DIY or Call Us?

You can safely check a failing fence yourself: walk the line and note which posts lean, measure gate sag with a level, and photograph any rust or chalking. What you shouldn’t do is dig out and reset a footing on a slope or pull a loaded gate off its hinges alone – both carry real injury risk and both can damage the fence further if the footing geometry is wrong. The aluminum itself is light, but a whole panel section is awkward and sharp, and getting a new post plumb in Glendale’s clay without proper drainage is where most DIY installs fail inside two years. Call (844) 320-5930 for a free estimate – we’ll bring a written price and the photos.

FAQs

A new front entry door with glass sidelights

Ideas for every part of the house

Kitchens, baths, roofs, windows, fences and patios: the projects that make a house work better inside and out.

Read our project guides
New painted shaker cabinets with an organized deep drawerA remodeled hall bathroom with patterned floor tile and painted wallsA remodeled kitchen with a waterfall island and wood cabinetsA wood double vanity with two mirrors after a bathroom remodelA newly finished roof with a ridge vent and step flashingA galley kitchen opened up to the dining room with a new peninsula

Explore more projects

Every project below starts the same way: a free on-site visit and a written price.

Getting started with Rowan in Glendale

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Your Glendale team

A local vetted partner works across Glendale and the towns around it, to the same written standard as every Rowan job.

Areas we serve
A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 320-5930
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Rowan Construction Group Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch