







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Driveway & Pavers: The Glendale Owner’s Guide
We install and repair Jerith-compatible driveway and paver systems throughout Glendale, and a full paver driveway installation here typically runs $7,000 – $18,000 depending on square footage, base prep, and paver selection. Smaller repairs, resetting, and paver replacement sit well below that. We’re an independent service provider, not affiliated with Jerith.
Owners usually find us one of two ways: a section of pavers has heaved or settled after a wet season, leaving a trip ledge at the driveway apron, or a paver has cracked and the joint sand is washing out with every hose-down. In Glendale’s older hillside lots, that heaving is often the base telling you something, not the paver itself.
Key Takeaways
- Jerith-compatible paver installation in Glendale runs $7,000 – $18,000; repair and reset work is priced per section.
- Most “failed” paver complaints trace to base compaction and drainage, not the paver unit.
- You get a flat written price, a documented photo record, and the 365-Day Done Right Promise.
- Call (844) 320-5930 for a free estimate and a line-by-line written quote.
Which Jerith Models This Applies To

Jerith makes vinyl and composite fencing, railing, and landscape border products, and its paver and border lines are commonly used as driveway edging, planting-strip borders, and decorative inlay strips within a larger hardscape. If you’re matching a replacement piece, the identification step matters more than the brand name. Look for a stamped or molded mark on the underside or the cut end of the unit, measure the actual face dimensions to the sixteenth of an inch, and note the profile depth. Jerith’s molded border and edging profiles have changed dimensions across production runs, so a “same” piece ordered by color name alone can arrive a quarter inch off and refuse to seat against the existing run.
On the OEM-versus-aftermarket question for Jerith specifically, the honest answer is that color and profile matching is the whole ballgame. A generic paver border in “the same color” will almost never match a weathered Jerith run after two or three California summers, because vinyl and composite fade at different rates than cast concrete or clay. Where an exact Jerith profile is still available, matching it is the cleaner path. Where it isn’t, we set the new piece and let the crew photograph the joint so you can see the match before we close out. The same sourcing discipline we apply to KraftMaid, Cambria, and Silestone work applies here: name the part, verify the spec, write it down.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Driveway & Pavers Is Failing
Here are the symptoms we actually see on Glendale driveways, and what each one is telling you.
- Heaving or a rocking paver at the apron. Usually a base compaction or drainage problem underneath – water is pooling and freezing the joint open. The paver is the messenger, not the cause.
- Cracked or chipped border units. Vehicle load over an edge that wasn’t set deep enough, or a border run with no restraint. Cracks at the same spot every season point to edge restraint, not bad material.
- Joint sand washing out after rain. Poor drainage slope or missing polymeric joint sand. Glendale’s dry spells followed by heavy rain push water through faster than sand can hold.
- Color fading or chalking on the sun-facing run. UV exposure on vinyl and composite borders. Fading is cosmetic; once the surface chalks, though, it won’t take a sealer evenly.
- Loose or lifted edging along a planting strip. The border wasn’t anchored to the base course. This one is a real trip hazard at the driveway edge and worth fixing before someone catches a foot on it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Jerith-compatible paver driveway installation in Glendale runs $7,000 – $18,000. A paver patio installation is $3,500 – $11,000. If the existing driveway needs full replacement, that’s $5,000 – $14,000. Sealing an existing surface is $250 – $700, and concrete driveway installation, if you’re comparing materials, is $4,500 – $12,000.
What moves you within those ranges: square footage, excavation and haul-off, base depth, drainage corrections, and paver selection. Parts-plus-labor is shown as separate lines so you can see what the material costs versus what the install costs. Under Clause 1 of the Haven Standard, you get a written price before any work starts, and no change proceeds without a signed change order. Every visit includes a documented photo record of what we found and what we did. The 365-Day Done Right Promise covers the workmanship.
DIY or Call Us?
You can safely check a few things yourself: measure the heaving or settling, photograph the joint pattern, note where water pools after rain, and confirm the paver dimensions. What goes wrong for most owners is the base. Resetting a paver without re-compacting and re-grading the base underneath just buys you another season before the same spot heaves again. And a paver edge that isn’t restrained properly is a genuine trip hazard for anyone using the driveway.
This part isn’t dangerous to handle the way a garage-door spring is, but base failure and drainage corrections are where the real work sits, and that’s the part that determines whether the fix lasts. If you’ve already reset the same section twice, it’s time to look underneath. Call (844) 320-5930 for an exact quote – estimates are free, and we’ll walk the driveway with you and show you what we’re seeing.
FAQs

A properly installed paver driveway with a compacted base typically lasts 25 – 30 years, and Jerith vinyl or composite borders hold up well in Glendale’s climate – the material isn’t the weak point. The base is. If the base was under-compacted or the drainage slopes the wrong way, you’ll see failures within 3 – 5 years regardless of the paver. Call (844) 320-5930 for a free inspection if yours is aging.
Yes, in most cases. A single cracked or heaved section, washed-out joint sand, or a loose border run can be reset and re-sanded without touching the rest of the driveway. Full replacement is only necessary when the base is failing across a wide area or the surface has chalked beyond sealing. We’ll tell you honestly which one you’re looking at.
A section repair runs one to two days, including base re-compaction and joint sand. A full paver driveway installation runs three to five days for a typical Glendale single-car or double-car width, depending on square footage and site access. We give you the schedule in writing before we start.
We match by profile, dimensions, and color against the existing run, then source OEM where available and quality-compatible equivalents where it isn’t. You’ll see the part spec in the written quote, and we photograph the joint before leaving. Call (844) 320-5930 to start the match.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












