A Rowan company - serving Glendale, CA
A remodeled primary bathroom with a soaking tub and a walk-in shower
James Hardie · Glendale

James Hardie Bathroom Remodeling in Glendale, CA

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Glendale
A remodeled primary bathroom with a soaking tub and walk-in shower
A freestanding soaking tub in a remodeled primary bathroom
A walk-in shower with large-format tile and a built-in niche
A remodeled family room with new windows and a window seat
A standing-seam metal roof over a covered porch
A new bay window with a cushioned seat
A new wood side gate with black hardware
A new concrete driveway with a paver border
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

James Hardie Bathroom Remodeling: The Glendale Owner’s Guide

James Hardie bathroom remodeling work in Glendale, CA typically runs $9,000 – $28,000 installed, with smaller baths landing around $5,000 – $12,000. We’re an independent Glendale contractor, not affiliated with James Hardie, and we work with the brand’s fiber cement backer and tile systems because they hold up to the moisture load a Glendale bathroom actually sees. Same-day response applies to scheduling and inspections, not to a full remodel; nobody rebuilds a bathroom in an afternoon.

Call (844) 320-5930

Most Glendale owners don’t discover a James Hardie problem on a schedule. It surfaces when a floor tile shifts underfoot, when a shower wall feels spongy a few inches above the pan, or when a baseboard swells near the vanity after a slow leak the homeowner never saw. The part that failed is usually not the cement board itself. It’s the joint, the fastener, the tape line, or the waterproofing layer the board depends on.

Which James Hardie Systems This Applies To

A tile setter installing wall tile in a shower

James Hardie doesn’t sell a single “bathroom part.” It sells a tile backer and substrate family, and the piece you buy depends on which line your contractor spec’d. The two you’ll meet in a Glendale bathroom are HardieBacker 500 and the older HardieBacker 1/4-inch, plus the various tape, screw, and membrane accessories that go with them. HardieBacker 500 is the current standard for wet walls and floors at 1/2 inch; the 1/4-inch version was common on floors in past installs and is thinner than most modern recommendations want.

How to identify what you actually have: pull a vent cover or a loose piece of trim, then look at the backer edge. The board should read HardieBacker and show a thickness stamp near the corner. Measure the thickness with a tape – 0.42 inch is nominal 1/2 inch, 0.26 inch is nominal 1/4 inch. If the board is gray-blue with a printed grid on one face, it’s the current line. If it’s a different color or has no grid, you’re likely looking at a competitor or an older Hardie spec, and the right replacement part may not be a Hardie part at all.

The OEM-versus-aftermarket decision for James Hardie is unusually simple compared to plumbing or appliance parts. Aftermarket fiber-cement backer sold at a Glendale building supply is functionally interchangeable at the sheet level, but the accessory line – the tape, the screws, the joint treatment – is where the brand’s spec matters. Using Hardie’s matched tape and screw set with a competitor board is fine; using a competitor’s tape and screws on Hardie board can void the assembly. We source and match by spec, not by what happens to be on the shelf.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your James Hardie Bathroom Remodeling Is Failing

  • Spongy or soft spots in the shower wall. The board has absorbed water because the joint failed upstream, usually at the tape line or a screw head, not because the cement board itself degraded.
  • Grout cracking in a straight line across the floor. Movement in the subfloor or the backer is transferring through; a 1/4-inch board on a floor without proper underlayment is the common culprit.
  • Water staining at the baseboard or the shower curb. The waterproofing layer has breached and water is wicking into adjacent drywall or framing – this is the symptom that costs the most in Glendale, where original 1920s homes often have wood framing under tile.
  • Cracked or hollow-sounding tile in a wet zone. The tile has de-bonded from the backer, which in a shower means the assembly is no longer waterproof regardless of what the surface looks like.
  • Visible mold or efflorescence in the grout joints. Persistent white mineral bloom and green-black spotting mean the substrate is staying wet; the board is fine, the waterproofing behind it isn’t.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A finished backyard cottage with a small covered porch

Bathroom remodeling in Glendale lands at $9,000 – $28,000 installed. Smaller baths fall at $5,000 – $12,000. Within a James Hardie-focused scope, the line items we quote look like this:

Scope Glendale installed range
Walk-in shower installation $4,500 – $12,000
Tub-to-shower conversion $3,500 – $10,000
Shower replacement $3,000 – $8,500
Bathroom vanity installation $800 – $3,000
Full bathroom remodel $9,000 – $28,000

What drives the number: square footage, whether the existing pan and curb stay or go, how much rot is found once the board comes off (the single biggest wildcard in older Glendale homes), and whether the layout moves a drain or a supply line. Fixture selection matters too – Kohler and Toto move the number more than the board does. Our price is a flat written number with a written scope before work begins. Under Clause 1 of the Haven Standard, the price is written before anyone starts. If we open a wall and find rot, work stops until a change order is signed. No exceptions. Workmanship is covered by the 365-Day Done Right Promise.

DIY or Call Us?

An owner can safely do this much: check for spongy spots by hand, look for cracked grout, pull a vent cover to identify what board is behind the wall, and note where water staining appears. That’s diagnosis, not repair.

Where DIY goes wrong with James Hardie bathroom work: the board is easy to hang badly and hard to hang correctly. It must be set on a flat substrate, screwed with the right washer-head screws at James Hardie’s specified spacing, taped with the matching tape, and then covered with the correct waterproofing for the wet zone. Get one of those wrong and the assembly fails in 12 to 24 months, not in 12 years. A Glendale owner who installs tile over a bare board with thin-set and no waterproofing has built a shower that will leak. This is also wet-wall work at electrical and plumbing penetrations, which is not a safe place to learn. Call (844) 320-5930 for a free written estimate before you consider replacing the board yourself.

FAQs

A new roof with clean valleys and new flashing

How long does a James Hardie bathroom assembly last in Glendale?
A correctly installed assembly with proper waterproofing lasts 25 to 40 years. In Glendale – where slab-on-grade homes can hold moisture in the bathroom floor framing and where older homes often lack a modern vapor barrier – the failure window compresses to 12 to 20 years unless the waterproofing layer and joints are done to spec. Call (844) 320-5930 for an exact quote on your bath; estimates are free.

Can the failed section be repaired instead of replaced?
Sometimes, yes. A localized grout or tape failure can be corrected without tearing out the whole room; a spongy wall or a breached pan cannot. We open the suspect area, photograph what we find on the documented photo record, and quote the repair versus the replacement with both numbers in writing. Call (844) 320-5930 to schedule the inspection.

How long does the swap take?
A shower or floor tear-out and rebuild usually runs three to seven working days on site, with tile cure time added. A full bathroom remodel is two to four weeks. We give the schedule in writing with the price, and change orders – signed before any work proceeds – cover anything the demo reveals. Call (844) 320-5930 for a written timeline on your specific bathroom.

How do you source the James Hardie part?
We source by spec – board thickness, tape, screws, and waterproofing matched to the assembly James Hardie publishes, not substituted for what’s on the shelf. We don’t carry parts on a truck and don’t stock locally; we order matched to your job and confirm the spec before install. We also work with KraftMaid, Cambria, and Silestone on the same bath where those brands are in scope. Call (844) 320-5930 and we’ll tell you exactly what your bathroom needs.

Rowan Construction Group Glendale is an independent construction contractor serving Glendale homeowners. Call (844) 320-5930 for a free estimate, a written flat price, and a documented photo record on every visit.

Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.

Ideas for every part of the house

Kitchens, baths, roofs, windows, fences and patios: the projects that make a house work better inside and out.

Read our project guides
A new white vinyl privacy fence with a double gateNew painted shaker cabinets with an organized deep drawerA remodeled kitchen with a waterfall island and wood cabinetsA new multi-panel patio door opening a kitchen to the patioA new stained cedar privacy fenceA new paver patio with a seat wall and fire pit

Explore more projects

Every project below starts the same way: a free on-site visit and a written price.

Getting started with Rowan in Glendale

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Your Glendale team

A local vetted partner works across Glendale and the towns around it, to the same written standard as every Rowan job.

Areas we serve
A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 320-5930
Local Service Coverage

Request a Free Estimate in Glendale

Tell us what you need - Rowan Construction Group Glendale responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch