







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Glendale Owner’s Guide
Boral fence installation in Glendale typically runs $3,500 to $9,000 installed for most residential lots, with the exact number driven by linear footage, gate count, and how much old fence has to come out first. We install Boral-compatible fence systems and set every post in concrete to a written scope, so the quote you sign is the quote you pay. If you are here because a rail has cracked, a post has started to lean after a rain, or you cannot find the matching Boral panel size at any yard in the county, you are in the right place.
Which Boral Models This Applies To
Boral’s fence line covers composite/wood-plastic boards and the capped composite systems sold through building supply yards, and the model line matters because the board profile, cap thickness, and tongue-and-groove dimensions change between series. The matching problem is not which brand you bought, it is which generation of that brand sits in your yard. Pull a board and look at the back face for a series stamp or lot code; if there is none, measure the board’s actual face width and thickness to the nearest 1/16 inch and count the slots or flutes. An OEM replacement board protects the color match and the manufacturer’s own board warranty. A quality aftermarket equivalent (there are several that copy the same flute profile) can cost 20-30 percent less per linear foot and will fit the rail, but the color will drift against a sun-faded run of Boral within a season or two in Glendale’s UV load. On any install over about 40 linear feet, we will not mix OEM and aftermarket on the same face; the mismatch is visible from the street.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Fence Installation Is Failing
- Cracked or split rails at the fastener line. Composite boards crack where a screw was driven too close to the edge or without a pilot hole. The crack starts at the fastener and runs to the board end; it is a fastening failure, not a bad board.
- Posts leaning after rain or an irrigation cycle. A post leans when the footing was set too shallow or the soil was not compacted. Glendale’s clay-heavy soil in the foothill neighborhoods swells and shrinks across the wet/dry cycle, and a short footing will work loose.
- Fading or color shift on one run but not the next. Composite fades with UV. If one section has gone pale gray and the adjoining run has not, the sections were likely supplied in different lots or the older run is simply aged.
- Boards rattling or lifting out of the rail channel. The cap or the retaining clip has failed, or the rail was cut too deep, so the board has nothing to seat into. Check the rail’s channel depth against the board thickness.
- Loose or sagging gates. Gate failure is almost always hardware and hinge-post movement, not the Boral panel. An undersized hinge post or a post set without a brace will drop the gate within a few seasons.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Boral fence installation in Glendale falls in the $3,500 to $9,000 range for a typical residential property. What moves the number: linear footage, gate count, whether old fence and footings must be removed (hauling and concrete takedown add to the total), and whether the posts need new footings set in concrete. Board replacement on an existing Boral run costs far less than a full install; the price depends on how many boards and rails and whether the posts are sound. Our written price is a flat number with a written scope: materials, labor, footing depth, gate hardware, cleanup, and hauling, all line-itemed before anyone touches a tool. Under Clause 1 of The Haven Standard, no work proceeds on a change until the change order is signed. If we find a rotten footing under the fence line, you get a documented photo record and a written change order to approve, not a verbal “we found some extra.” The work carries our 365-Day Done Right Promise: if it is not right, we make it right, per the written terms.
DIY or Call Us?
You can safely check a lot of this yourself: walk the fence line after a rain and note which posts move, pull one board to read the series stamp, measure board width and thickness, confirm gate hardware and hinge posts, and clear soil and vines away from the base to see the footings. Where owners go wrong is the structural side. Setting a post footing to depth in Glendale’s clay, digging through a buried irrigation line or gas stub, loading a fence line across a property line, and matching a Boral board to an existing run without reading the flute profile are all jobs that look simple and go sideways. Fence work near utility lines, gas stubs, and property corners is where we spend the most time fixing DIY starts. We are an independent contractor, not affiliated with Boral, and we will tell you plainly what needs replacement and what does not.
FAQs

A well-installed Boral fence in Glendale commonly holds up 15 to 25 years, and how long it actually lasts comes down to the footing more than the board. The composite panel itself resists rot and termites far better than wood; the posts and footings are where failures show up first. In the foothill and canyon edges where soil movement is greater, a properly braced hinge post and a concrete footing set to depth buy you the difference. Call (844) 320-5930 for a free estimate on a full replacement.
Often yes. Cracked rails, loose boards, failed caps, a single leaning post, and gate hardware are all repairable without replacing the whole run. If the posts and footings are sound along most of the line, we will quote a repair and show you in the photo record exactly what we found. Full replacement only makes sense when several posts have moved or the runs have gone brittle from UV. Call (844) 320-5930 for a free estimate and we will tell you which it is.
A board or rail replacement on a Boral run is usually a one-day job. A full fence installation runs longer and depends on footage, gate count, whether old footings come out, and whether the line needs re-laying. We put the timeline in the written scope before work starts so you are not guessing. Call (844) 320-5930 for a free estimate with a written schedule.
We match the part to your existing model line using the series stamp, lot code, and physical board measurements, then source the OEM board or a quality aftermarket equivalent through a building supply yard. We do not stock parts or carry them on a truck; we order to the job, so your board comes in matched to the run it is joining. If the OEM board is discontinued, we will say so up front and show you the aftermarket match and its color variance before you commit. Call (844) 320-5930 for a free estimate.
We also install and match the other brands our Glendale customers bring us, including KraftMaid, Cambria, and Silestone where those come up in a wider project. For a Boral fence installation in Glendale, call (844) 320-5930 for a free estimate. You will get a flat written price with a written scope, a documented photo record on every visit, background-checked and uniformed technicians on site, and a live person answering the phone 24/7.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












