







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Driveway & Pavers: The Glendale Owner’s Guide
We install Boral-compatible driveway and paver systems throughout Glendale, and installed pricing typically runs $7,000 to $18,000 for a full paver driveway, with paver patios at $3,500 to $11,000. Smaller repairs and paver replacements are quoted individually. We’re an independent service provider, not affiliated with Boral, so we source parts and pavers against your actual profile rather than a catalog picture.
Owners usually find the problem slowly. One or two pavers rock underfoot when you cross the driveway. Sand starts washing into the gutter after rain. A hairline crack spreads across a field paver over a summer. Sometimes it’s a joint that’s gone from tight to a half-inch gap. All of those are signs the base, the setting bed, or the paver itself is failing, and the fix depends on which one it is.
Key takeaways:
- Boral paver failures in Glendale are more often base or bedding problems than bad pavers.
- Match the part to the actual paver profile, not to a photo on a website.
- Written flat price before work starts, every time.
- Documented photo record shows you what failed and what we did.
Which Boral Models This Apply To

Boral makes pavers in several families: the traditional Old Town, the larger-format Brookstown and Beechwood lines, and the tumbled and textured series used in place of concrete for driveways and patios. Each has its own nominal dimensions, thickness (often 60mm for driveway-rated product, thinner for patios), and edge profile. Thickness is the one that matters most for a driveway, because a paver rated for foot traffic will shear under a vehicle’s wheel load.
Identifying the right part starts with measurement, not memory. Pull one loose paver, measure its width, length, and thickness with a tape, and photograph the surface texture and edge style. If you have leftover pavers under the house or in the garage, bring one out. Boral’s molding and color batches change over time, so a “same color” paver from a current run may not match a driveway installed years ago. That’s a genuine compatibility gotcha: color, texture, and dimensional tolerance can differ between production batches, and getting them wrong is why a repair shows as a visible patch.
OEM Boral pavers give you an exact match when the original line is still in production. Where it isn’t, a quality aftermarket paver of the same thickness and a close color profile can serve, but only if you accept a visible repair area. We’ll tell you which is the honest choice for your driveway.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Driveway & Pavers Is Failing
- Pavers rocking underfoot or under wheels. This almost always means the bedding sand has shifted or the base wasn’t compacted properly at installation. The paver itself isn’t usually the problem; the layer beneath it is.
- Sand washing out after rain. Loose joint sand in the gutter or at the driveway edge signals joint sand loss or a drainage problem. In Glendale, where the occasional heavy winter storm runs water hard against a driveway edge, this shows up fast.
- Cracks running across individual pavers. A hairline crack that widens over months points to a point load on a paver that’s lost base support underneath. Cracking across the joint lines usually means the base has failed in a broader area.
- Gaps opening at the joints. Joints that go from tight to visible gaps mean the pavers are moving, and the setting bed is giving way. This is the earliest warning sign and the cheapest moment to address it.
- Efflorescence or white bloom on the surface. That white haze is mineral salt migrating out of the concrete or mortar. It can indicate moisture trapped in the base or a poor drainage slope, not just a surface stain.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed costs in Glendale depend on the size of the area, the paver profile, the condition of the base, and whether existing pavers have to be lifted and reset. Here’s what we quote:
- Paver driveway installation: $7,000 – $18,000
- Paver patio installation: $3,500 – $11,000
- Concrete driveway installation: $4,500 – $12,000
- Driveway replacement: $5,000 – $14,000
- Driveway sealing: $250 – $700
What drives the range: total square footage, whether the base needs re-compaction or a fresh layer of crushed aggregate, and the paver line you choose. Under Clause 1 of the Haven Standard, your written price arrives before any work starts, with a written scope and a written warranty. If the substrate turns out to need more than the original scope, no work proceeds on that change until you’ve signed a change order. That’s the discipline behind the flat quote, and it’s why projects finish within a few percent of the agreed number.
DIY or Call Us?
What you can safely check yourself: whether pavers are loose, whether joint sand is present and at the right level, and whether water pools anywhere after rain. Those give you a clear picture of what’s happening. What’s harder is the base. Replacing a paver over a compacted, stable sand bed is a reasonable homeowner job for a few isolated units. Replacing pavers over a failing base without addressing the base is where it goes wrong: the new paver sits on the same soft spot and fails again within a season.
For anything involving a large area, a shifted base, or pavers bearing vehicle loads, the base prep and compaction are the whole job. That’s not a job to guess at. Call (844) 320-5930 for a free estimate, and we’ll tell you what the photo record shows before any work is scheduled.
FAQs

A properly installed Boral paver driveway can hold up for 25 to 30 years or more; the failure points in Glendale tend to be base settlement and joint sand loss rather than the pavers themselves. The region’s dry summers and periodic winter rain are hard on the setting bed, not usually on the paver surface. Call (844) 320-5930 for an inspection quote if you’re seeing shifts.
Yes, in many cases a single cracked or lifted paver can be pulled and reset over a repaired spot. Whether a repair holds depends on the base underneath it; a repair over a failed base will reappear within a season. We’ll tell you whether a repair or a replacement is the honest call before you commit. Call (844) 320-5930 to talk it through.
A single-paver replacement is often done in a few hours; a section reset or joint sand restoration may take a day depending on area size and how much base work is needed. We’ll give you a written time and scope before we start. Call (844) 320-5930 for an estimate.
We measure the existing paver at the job site, photograph the profile and color, and source to that exact spec, checking dimensional tolerance and thickness rather than relying on a color name alone. If the original line is discontinued, we’ll tell you and quote a quality aftermarket match with an honest note about visible patch. Call (844) 320-5930 for a free second opinion on any written estimate.
We also service related trades and materials under our foundation, including KraftMaid, Cambria, and Silestone products for other parts of your home.
Call (844) 320-5930 for a free estimate on your Boral driveway or paver repair in Glendale. We’ll bring a written flat price before any work starts, answer a live person whenever you ring, and leave a documented photo record of what we found and what we did.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












