







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Fence Installation: The Glendale Owner’s Guide
Barrette fence installation in Glendale typically runs $3500 – $9000 for a full residential run, and we schedule most installs within the same two-week window from the first site visit. If you already own the panels or posts and need them set correctly, the number drops toward the low end. Most Glendale owners discover a failed part the same way: a gate that starts dragging on the hinge side, a post that loosens after the first Santa Ana wind, or a panel that leans a few degrees out of plumb six months after install. The fence looked fine at handoff. Then the soil moved.
Glendale sits on decomposed granite and clay-heavy soils that swell in the wet months and shrink hard by August. That movement is unforgiving on footings, and it is the first thing we check on any fence call.
Key Takeaways
- Full Barrette fence install in Glendale: $3500 – $9000 installed, parts and labor together.
- The part that fails first is almost always the footing, not the panel or picket.
- We’re an independent contractor, not affiliated with Barrette. We install to their specs.
- Written price before any work starts. No change order gets signed without your approval.
Which Barrette Models This Applies To

Barrette’s residential fence lines break into three families worth knowing: the vinyl privacy lines (Bufftech and similar profiles), the aluminum ornamental runs, and the composite and hybrid products. Each has distinct post dimensions and rail profiles, and the parts are not interchangeable across families. A 5-inch vinyl post sleeve will not accept a rail bracket designed for a 4-inch post column, and buyers regularly order the wrong bracket because the panel label only lists the panel.
To identify your exact product, look for the manufacturer stamp on the inside face of a post or the underside of a top rail. Barrette stamps most of their lines with a series code and a profile measurement. If the stamp is gone, measure the post column at the outside face (Barrette’s common residential posts run from 4-inch to 5-inch square in vinyl) and measure the rail height. Bring both numbers to us and we can usually match the part in a single call.
On the OEM-versus-aftermarket question: for structural brackets, post caps, and gate hardware, OEM Barrette parts fit correctly and hold their wind rating. For pickets and infill panels, a quality aftermarket vendor can match the profile at lower cost, but only if the color and surface finish match. We note on every quote which parts are OEM and which are aftermarket matches, so the number you see reflects exactly what you’re getting.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Fence Installation Is Failing
Five symptoms come up again and again on Glendale calls, and each one traces to a specific cause:
- Gate sagging on the latch side. The hinge post has lost footing or the hinge hardware has wallowed out its holes. A gate is the heaviest load on the fence, so it exposes footing issues first. In Glendale, this often shows up on the south or west run where soil dries fastest.
- Posts leaning or loose after wind. The post footing was set too shallow or in soil that wasn’t compacted. Barrette specifies a footing depth based on frost line and local load, and Glendale soil behavior means a shallow footing that held in spring will not hold through summer.
- Panels bowing or rails pulling free. Rail brackets have cracked, or the screw heads have snapped. Vinyl and aluminum rails expand and contract with temperature, and a rail set tight with no expansion gap will bow.
- Color fade or chalking on the surface. UV exposure in Southern California is high, and older vinyl formulations chalk faster here than the manufacturer’s stated lifespan suggests. A six-to-eight-year fade pattern is realistic on an unshaded run.
- Rust streaks or white powder at hardware. The brackets or fasteners were not the correct coated grade for exterior use. Glendale’s dry heat and occasional marine layer accelerate corrosion on the wrong hardware.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A full Barrette fence installation in Glendale runs $3500 – $9000. That range covers a typical residential side and rear run, including removal of the existing fence, new footings, posts, panels, and gate hardware. A single-part replacement (one bracket set, one post cap, one loose footing re-set) will land at the low end of that range; a full replacement with a walk gate at the high end.
What drives the number:
- Linear feet. A common Glendale lot run of 80 – 120 feet sits in the middle of the band.
- Footing conditions. Decomposed granite or clay-heavy spots require deeper footing work, which is where the range tops out.
- Gate count and type. A walk gate adds cost; a double drive gate adds more.
- OEM vs. aftermarket parts. OEM brackets and caps cost more; we name which we’re using on every line.
The quote is a flat written price, not an estimate that gets revised at the end. Under our standard, no work proceeds on a change without a signed change order, so the number you agree to is the number you pay within a few percent across our projects. The work is covered by our 365-Day Done Right Promise: if the install fails, we make it right. Every job includes a documented photo record of what we found and what we installed.
DIY or Call Us?
Some checks are safe to do yourself: walk the fence line and note which posts move by hand, look for cracked brackets, and check whether gate hinges are loose or the footing has shifted. A homeowner with basic tools can tighten or replace a gate hinge and swap a post cap without any risk.
Where DIY goes wrong is the footing. A fence post footing has to be set at the right depth for the local soil, with the right concrete and the right drainage, and a bad footing does not fail immediately. It fails one windy season later, after the warranty window on amateur labor has closed. Re-setting a post in uncompacted Glendale soil is one of those jobs that looks simple and isn’t. Digging into a footing near a property line without knowing where utilities run is also a real hazard, and that’s a call-before-you-dig question, not a guess.
For rail bracket replacements and gate hardware, we can advise over the phone and give an exact quote. Call (844) 320-5930 and we’ll tell you within the call whether it’s a parts swap or a footing job.
FAQs

A properly installed Barrette vinyl fence can hold its structure for 15 – 25 years in Southern California conditions, though the surface finish will chalk and fade noticeably sooner on unshaded runs. The color fade is cosmetic; the structural life depends almost entirely on the footing. If the footings were set correctly, the fence will outlast the finish. Call (844) 320-5930 for an honest assessment of your existing fence before deciding to repair or replace.
Often yes. A cracked rail bracket, a bowed picket, a loose post cap, and a worn gate hinge are all individual-part swaps with no need to touch the rest of the fence. A loose post is a footing repair, not a full replacement, unless the post itself has split. We tell you on the first visit which category you’re in before quoting anything. Call (844) 320-5930 to schedule the assessment.
A single bracket or hardware swap takes under an hour at your property. A post footing re-set takes a partial day because the concrete needs to cure before the rail and panel go back on. A full replacement run typically runs one to two days depending on linear footage and gate count. You’ll get the actual schedule in writing with the quote.
We source OEM Barrette parts through licensed distributors and match the series code from the stamp on your existing post or rail. If the OEM part is discontinued, we identify the closest aftermarket match by profile measurement and finish, and we list it explicitly on the quote as an aftermarket match. You will always know which parts are OEM and which are equivalents before any work starts. Call (844) 320-5930 with your existing part in hand and we can usually confirm the match on the call.
We also work with KraftMaid, Cambria, and Silestone on adjacent interior projects if the fence work turns into a bigger scope, though this page is about fence installation only.
If you’ve got a Barrette fence that isn’t holding in Glendale, the diagnosis is usually quick and the quote is free. Call (844) 320-5930 for a written price before any work starts. We’ll bring a line-item quote, name every part by OEM or equivalent, and leave you with the photo record of what we found.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












