







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Kitchen Remodeling: The Glendale Owner’s Guide
We install Atlas-compatible kitchen remodeling in Glendale at a typical installed price of $14,000 – $45,000 for a full kitchen, $9,000 – $20,000 for a small kitchen, and $4,000 – $13,000 for cabinet installation alone. Rowan Construction Group Glendale is an independent contractor, not affiliated with Atlas, and we quote a flat written price before any work starts. Most owners call us after a cabinet door stops closing flush, a drawer box cracks along the bottom rail, or the finish starts lifting near the sink where steam hits it daily.
Which Atlas Models This Applies To

Atlas kitchen cabinetry shows up in Glendale homes in a few recognizable forms: builder-grade slab-door runs from the 2000s, semi-custom shaker and raised-panel lines, and the modern frameless boxes with full-overlay doors. The part that matters most is the cabinet hardware and box construction, because that’s what fails. To match the right replacement, look for the Atlas label inside a cabinet door or on the back panel: it usually carries a model code and a box depth (commonly 12″ or 24″). Measure the existing door height and width to the nearest 1/16″ and note whether the hinge plate is side-mount European (35mm cup) or face-frame. A 35mm hinge bore is standard, but Atlas used both 32mm and 35mm cup patterns depending on the line, so the measurement is the compatibility check that saves a return trip.
On the OEM-versus-aftermarket call: for hinges, drawer slides, and shelf clips, a quality aftermarket equivalent (Blum, Grass, or KV) usually outlasts the original and fits the same bore. For door fronts and finished panels, matching an Atlas stain or laminate is where aftermarket gets tricky, and that’s the part we take the most care sourcing through our vetted brand network. We also work with KraftMaid, Cambria, and Silestone when an Atlas line has been discontinued and a full swap of a cabinet run or countertop makes more sense than chasing a single orphan door.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Atlas Kitchen Remodeling Is Failing
- Doors that won’t stay closed or hang crooked. The hinge cup screws have stripped the particleboard, or the hinge arm bent. Particleboard loses its grip after a few open-close cycles once damp – common near a Glendale kitchen sink.
- Drawer boxes cracking at the bottom rail. The staples or dado joint give out under the weight of pots and cast iron. A cracked box means the load rating was exceeded, not that you did anything wrong.
- Finish lifting or flaking near the sink and range. Steam and heat from daily cooking swell the substrate under the laminate or paint. Glendale’s dry summers and wet winters push that expansion-contraction cycle harder than a mild climate would.
- Soft-close mechanism failing (slamming drawers). The dampener inside the slide wears out or the slide rail wears a groove. Sourced slides are usually the fix, not the whole cabinet.
- Cabinet box separating from the wall or leaning. Loose anchor screws or a failing toe-kick under load. This one points to the install method, not the hardware, and it needs a look before it gets worse.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Every Glendale price we quote is a flat number in writing before the first tool comes out, with the scope spelled out: which doors, drawers, slides, and hinges we’re replacing, and how the finish will be handled. Here’s how the ranges break down for an Atlas kitchen:
| Item | Installed Range (Glendale) |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation (box + doors) | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
The range moves on cabinet box condition (rotted substrate pushes toward replacement), door style and finish (a custom stain match runs higher), and whether the countertop comes off to reach the cabinets. Hardware-only swaps sit at the low end; a full cabinet run with new countertops sits at the top. Every job gets our 365-Day Done Right Promise and a written workmanship warranty, and our technicians have up to 19 years of experience matching parts to the right box.
DIY or Call Us?
You can safely check most of this yourself: open a door and look at the Atlas label, measure the hinge bore, note a cracked drawer box, photograph the finish damage. Those are inspection steps, not repair steps. Where DIY goes wrong is the swap itself. Replacing a hinge with the wrong cup pattern wallows the screw holes; forcing a drawer slide into a worn dado cracks the box further; and a loose cabinet box that looks like a hardware problem can be a wall-anchor problem that needs to be fixed before anything is hung on it. A mis-drilled door front is expensive to undo.
If you’ve got the label and the measurement, that’s most of the battle. Call us at (844) 320-5930 and we’ll match the part, quote a flat written price, and include a documented photo record of what we found and what we swapped – not an optional extra.
FAQs

A well-installed Atlas cabinet box should run 15 to 20 years before the hardware needs attention, and the finish often fails before the box does – especially near a sink in Glendale’s dry-summer, wet-winter swing, which works the seams every year. If a box has separated from the wall or the particleboard has swollen and crumbled, replacement beats repair. Call (844) 320-5930 for a free estimate on what you actually have.
Yes, in many cases. Stripped hinge holes can be re-bored and re-seated, a worn slide can be swapped, and a single cracked drawer box can be replaced without touching the rest of the run. The judgment call is substrate condition: swollen or crumbled particleboard doesn’t hold a fastener, so a repair there just delays the same failure. We’ll tell you which you’re looking at, in writing, before any work starts.
A hardware-only swap (hinges and slides on a normal Glendale kitchen, roughly 15 to 20 doors) is a one-day job for most homes. A cabinet installation with new boxes, doors, and finish takes several days to a couple of weeks depending on the run and whether the countertop and backsplash are part of it. We give you the timeline in the written quote, not a verbal guess.
We work through our vetted brand network to find a matching or equivalent part, and where an exact Atlas match isn’t available, we name the compatible aftermarket option and the spec it fits – not a vague “close enough.” If a discontinued line leaves a single door or panel unmatched, we’ll quote the honest options side by side, including working with KraftMaid, Cambria, or Silestone where a larger swap is the better call. Call (844) 320-5930 – estimates are free, and we’ll review any written quote line by line.
If your Atlas kitchen is failing and you want a flat written price before anything starts, call Rowan Construction Group Glendale at (844) 320-5930 for a free estimate. We’ll match the part, document what we find, and put the number in writing before the first tool comes out.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












