







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Master Halco Driveway & Pavers: The Glendale Owner’s Guide
We can’t give you a firm price without seeing the drive, but paver driveway installation runs $7,000 to $18,000 installed in Glendale, paver patios run $3,500 to $11,000, driveway sealing is $250 to $700, and driveway replacement sits at $5,000 to $14,000. A driveway is a long-lead project, not a same-day fix. Here’s what we actually install.
The important thing to know up front: Master Halco is a fencing and outdoor-structure manufacturer, not a paver company. They make vinyl, ornamental iron, chain-link and wood fence systems, gates, and related hardscape accessories: retaining-wall kits, post anchors, and the driveway gate hardware that ties into a paver or concrete apron. So when a Glendale homeowner searches for “Master Halco” and a driveway, what they usually own is a Master Halco gate or fence line at the mouth of the drive, and the pavers under it. Rowan Construction Group Glendale is an independent contractor. We’re not affiliated with Master Halco. We install driveways, pavers and gate footings around their hardware all the time, and this page is written for owners whose Master Halco component has failed or whose pavers are failing where it was set.
Which Master Halco Models This Applies To

Master Halco’s catalog is organized by material and system, not by a single model number, so identifying your part means reading what’s on the ground rather than what’s on the box. Vinyl runs include the Contemporary, Privacy and Chesterfield-style lines; the ornamental iron side carries the Montage and Ironcraft families, and the chain-link side covers PermaFused and Galvanized systems. Entry gates for a driveway typically tie to a post anchor or a gate-frame kit plus hinges, rather than a model stamped on a sticker.
How to identify what you have: measure the post spacing center to center, note the rail height profile, and look for a manufacturer mark on the hinge, latch or post cap. That measurement is what matches the replacement. On the OEM-versus-aftermarket call, Master Halco hardware is often the right answer because the post anchor geometry and hinge patterns are specific to their systems. For gate hardware, a quality aftermarket hinge or latch from a reputable brand usually outlasts the original, since it’s a wear part. For pavers under the drive, the match is the actual problem: a Master Halco gate footings sits on a paved apron, and matching a discontinued paver face is harder than replacing the gate. We’ll say so before we quote.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Master Halco Driveway & Pavers Is Failing
- The gate sags or drags on the pavement. The post has shifted in the ground, usually because the footing was set shallow for Glendale’s clay-heavy soil or the paver base under the hinge post has settled. A gate that catches the drive is a footer problem, not a hinge problem.
- Pavers settle, heave or sink in a dip near the gate. Water is pooling instead of draining off. Where a Master Halco gate apron sits on a slope, runoff collects at the low corner and undermines the base over a few seasons.
- Rust streaks or white staining at the post. On iron, rust blooms at the anchor bolt; on vinyl, weathered discoloration at the post base. On a CA driveway, sun and irrigation both work against it. This points to the anchor or footing.
- Edge or border pavers spalling and shifting. The paver edge-restraint has failed. Once the border gives, the field pavers migrate and the drive starts fanning outward toward the street.
- Visible cracks along the driveway expansion joint. A joint that’s opened up is a substrate or drainage issue, not a surface crack, and it usually shows up first at the gate area where you cross each day.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

These are installed ranges for Glendale, calibrated to the current local market:
- Paver driveway: $7,000 to $18,000
- Paver patio: $3,500 to $11,000
- Concrete driveway: $4,500 to $12,000
- Asphalt paving: $3,500 to $9,000
- Full driveway replacement: $5,000 to $14,000
- Driveway sealing: $250 to $700
About what drives the number: drive size, material choice, the condition of the existing substrate (is there old concrete to remove and haul), grading for drainage, and whether the gate footing and post anchor are part of the job. We quote paver work at a flat written price with a written scope, so parts and labor land in one number you can hold onto: the pavers, the base aggregate, the edge restraint, the gate footing, labor and debris removal. No work starts until the change order is signed. The labor carries a 365-Day Done Right Promise. If it settles or fails within the year, we come back and make it right.
DIY or Call Us?
What you can safely check yourself is the diagnosis, not the fix. Walk the drive after a rain and take a photo of where the water pools. Take a level to the gate post to see if it’s plumb. Measure the post spacing. Confirm drainage flows away from the door.
Where it goes wrong: resetting a gate footing means the gate comes off, the anchor comes out, and the pavers under it are pulled up. If the footer is reset in soil that’s already settled, the gate sags again by the next season. And if the base under the pavers was wrong to start, repointing the surface hides the problem the rest of the way into failure. If the gate could fall with a push, don’t leave it, and don’t run the lawnmower against the post. Call us for an assessment. We’ll tell you the small version, the full version, and the price of each in writing.
FAQs

How long does a paver driveway last in Glendale? A properly installed paver driveway with a compacted base and edge restraint lasts 25 to 30 years in our area, longer than concrete, which crack and spall faster. The base and drainage matter more than the paver. If the base is right, the drive holds. If it isn’t, it fails early regardless of material.
Can a failing driveway be repaired instead of fully replaced? Yes, often. A sealing job at $250 to $700, a re-set border, or a single failed section of pavers can buy years when the rest of the base is intact. If more than a third of the drive has settled, a partial fix just pushes the problem to the next joint. Call (844) 320-5930 for an honest read before you commit to a full replacement.
How long does a paver driveway replacement take? A typical Glendale drive takes three to five working days: removal, base prep, compaction, setting, and finishing. Adding a gate footing and post anchor usually adds a day. Larger irregular drives or steep grades run longer. We give a written schedule with your quote.
How do you source Master Halco gate hardware and matching pavers? We source Master Halco parts through established supply channels and confirm the model before ordering. For pavers, we match the face, thickness and color as closely as the current supply allows, and we tell you where a match won’t be exact. The quote lists the part number and the paver line on paper, so there’s no surprise on delivery day.
We also install and service KraftMaid, Cambria and Silestone products on the interior side. If you want the drive or patio written up the way it should be, with a number before anyone breaks ground, call Rowan Construction Group Glendale at (844) 320-5930 for a free estimate. Bring a photo of the gate and the worst of the pavers, and we’ll show you the diagnosis and the price in writing.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












