







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Driveway & Pavers: The Glendale Owner’s Guide
We install CGI driveway and paver systems in Glendale, and for a typical residential driveway the installed cost runs $5,000 – $18,000 depending on whether you go pavers, concrete, or asphalt, with paver driveways at $7,000 – $18,000 and a full driveway replacement at $5,000 – $14,000. A paver patio runs $3,500 – $11,000. Most Glendale owners don’t call us until something has visibly gone wrong: a line of pavers has heaved after the rainy season, water is ponding against the garage threshold, joints are washing out sand with every hose-down, or the driveway edge has started to sink where a downspout dumps onto it. That sink-and-wash pattern is the usual first signal, and it almost always points to the base layer under the pavers rather than the pavers themselves.
Which CGI Models This Applies To

CGI pavers come in distinct profile families, and matching the replacement correctly depends on measuring what you already have, not guessing from a photo. The two measurements that matter most are the paver’s nominal thickness (most residential driveway pavers are 60mm or 80mm, and 60mm is the common failure point under vehicle loads when the base wasn’t compacted to spec) and the exact face dimensions, since interlocking patterns depend on precision. Check the underside of a lifted paver or the edge of the driveway run for a stamp; CGI, like most manufacturers, marks face dimensions and sometimes a series code there. If you’re matching an existing field, pull one intact unit and bring it in as your reference rather than ordering from a catalog image.
On the OEM-versus-aftermarket question: for pavers, a quality aftermarket unit that matches thickness and face dimensions will perform identically to OEM in a driveway application, because the performance lives in the base preparation and the joint sand, not the logo on the side. Where OEM matters is color-match on a partial replacement, since dye lots vary between runs and an exact match from the original batch usually isn’t available. We’re an independent contractor and not affiliated with CGI, so we’ll tell you honestly whether an OEM match is achievable or whether the honest answer is a border detail that disguises the transition.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Driveway & Pavers Is Failing
- Heaving or rocking pavers. A paver that rocks underfoot has lost its bedding sand and usually its base compaction. In Glendale, the summer dry period shrinks clay-heavy subgrade, and the first heavy rain then pumps the base loose.
- Sand washing out of the joints. Joint sand is the locking mechanism, not decoration. When it disappears season after season, water is channeling through the joints into the base instead of running off, which accelerates settlement.
- Ponding against the garage or foundation. This is a grading failure, not a paver failure. Glendale’s hilly lots make positive slope away from the structure easy to lose, and standing water at the threshold is the signal that the driveway pitch has flattened or reversed.
- Edge settling and spread. Pavers along the driveway edge migrating outward means the edge restraint has failed or was never set in concrete. Once restraint goes, the whole field loosens.
- Cracking or spalling in the concrete section. If your driveway is concrete, hairline cracks that widen seasonally point to subgrade movement. In Glendale’s expansive soils, that pattern shows up on driveways poured without a properly compacted base or adequate control joints.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here are the installed ranges we quote in Glendale, with the scope written before anyone starts:
| Service | Installed Price Range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Concrete driveway installation | $4,500 – $12,000 |
| Asphalt driveway paving | $3,500 – $9,000 |
| Driveway replacement | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
What moves the number: square footage, base depth required by your subgrade, whether old material needs hauling out, edge restraint and drainage corrections, and paver selection. The quote breaks out material and labor line by line so you can see exactly where the dollars sit. We use Belgard and Techo-Bloc paver lines among our vetted brands, and every driveway comes with our written workmanship warranty and the 365-Day Done Right Promise. If it isn’t done right, we make it right. You get a documented photo record of the base prep before the pavers go down.
DIY or Call Us?
You can safely check several things yourself: lift one paver and look at the bedding sand depth (it should be roughly 1 inch over a compacted base, not loose fill), check whether water drains away from the garage, and confirm the edge restraint is intact. What you shouldn’t tackle alone is base replacement and re-grading on a driveway slope, especially where the pitch runs toward the house. Getting that compaction and pitch wrong means the whole field fails again within a season, and the material cost is not recoverable. That’s where we come in. Call (844) 320-5930 and we’ll schedule a free estimate with a written price and scope before work starts. We also service KraftMaid, Cambria, and Silestone products if you’re planning a broader project.
FAQs

A properly installed paver driveway should give you 25 to 30 years or more. The pavers themselves rarely fail first; the base and joint sand do. In Glendale’s dry summers and wet winters, joint sand needs replenishing every 2 to 3 years to keep water from undermining the base. Call (844) 320-5930 for an honest assessment of what your driveway actually needs.
Often yes, if the problem is localized. A single settled section, a failed edge restraint, or washed-out joints can usually be lifted, re-based, and reset. Full replacement makes sense when the base has failed across the whole field or when more than about a third of the pavers show movement. We’ll tell you which situation you’re in and price both options. Call (844) 320-5930 to schedule a free estimate.
A typical residential driveway replacement in Glendale takes 3 to 7 working days depending on square footage, base work, and drainage corrections. Paver installs tend to run toward the longer end because of base compaction and joint sand. Weather can extend that during the rainy season. Call (844) 320-5930 for a schedule based on your specific driveway.
We source through our vetted supplier network and match against the measurements from your existing field, not a catalog guess. Where an exact dye-lot match isn’t available, we’ll say so and offer a border detail or transition instead of pretending a mismatch won’t show. Every material is specified in the written quote before ordering. Call (844) 320-5930 for a free estimate.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












