







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Glendale Owner’s Guide
We install and remodel kitchens to CGI-compatible specifications in Glendale, and the honest installed range for a full kitchen remodel here runs $14,000 to $45,000, with a small kitchen at $9,000 to $20,000 and a single cabinet run at $4,000 to $13,000. Kitchens get planned, not dispatched overnight, so we quote in writing and schedule the work rather than promising a same-day arrival. Owners usually find trouble before they go looking for it: a cabinet door that won’t stay adjusted, a countertop seam that has started to shadow, a drawer box that sags under a full load of dishes, or a backsplash grout line that darkens after every rain-heavy week. By the time the third drawer lets go, the question stops being cosmetic and becomes structural.
Which CGI Models This Applies To
Glendale has a lot of pre-war and mid-century housing stock, and most of the kitchens we walk into there carry cabinets and casework from several different eras. That matters for compatibility. CGI product lines change hardware standards by series, and a hinge pattern from one generation will not line up with the cabinet face of another without either a new drilling pattern or a conversion plate. We identify the right component by pulling one door and one drawer and reading what’s actually there: the hinge cup depth (usually 35mm on later European-style concealed hinges), the slide type (side-mount ball-bearing versus undermount soft-close), and any label inside the cabinet box or on the back of the door that names the series. Measure the door thickness too, since 16mm and 19mm doors flex differently and take different screws. On the OEM-versus-aftermarket decision, we’ll say this plainly: for hinges and slides, a well-made aftermarket equivalent is fine and often cheaper, but for anything load-bearing or face-matched, we source OEM-compatible parts so the finish and the geometry stay consistent. We’re an independent service provider, not affiliated with CGI, so we match by spec rather than by a logo on the box.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Kitchen Remodeling Is Failing
These are the failures we actually see in Glendale kitchens, and each one points at a different cause.
- Cabinet doors that drift out of alignment. Usually a hinge cup screw that’s stripped the particleboard or plywood behind it, not a bent hinge. Repeated tightening makes it worse, because each turn enlarges the hole.
- Drawer boxes that sag or scrape. Undermount slides lose tension or the rear mounting socket pulls free from the cabinet back. Full-extension boxes with heavy cookware load fail first.
- Countertop seams that shadow or lift. In Glendale’s summer heat cycling, an epoxy seam can move enough to show a hairline. That’s a substrate or adhesive failure, not a stain you can scrub out.
- Grout and caulk lines that keep darkening. Backsplash joints against a solid-surface counter need a flexible sealant, and rigid grout there cracks within a season or two of thermal movement.
- Water staining under the sink base. A slow supply or drain leak rots the cabinet floor from underneath. By the time the swelling shows on the surface, the base panel usually needs replacing.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Kitchen work in Glendale breaks down into line items, and we put the number on the page before anyone picks up a tool. Here’s what the market here runs:
| Scope | Installed range (Glendale) |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What drives the range is substrate condition, cabinet box count and configuration, countertop material and edge profile, and whether the electrical or plumbing has to move. We quote the parts and the labor as separate lines so you can see what you’re paying for, and we hold the price with a signed change order for any scope change. Every job carries the 365-Day Done Right Promise: if it isn’t done right, we make it right. Sourcing runs through a vetted brand list, including KraftMaid and Wellborn cabinets and Cambria and Caesarstone countertops, with CGI-compatible components matched by spec; we also service KraftMaid, Cambria, and Silestone kitchens.
DIY or Call Us?
There’s a real split here, and it’s worth being honest about it. You can safely check hinge alignment, tighten a loose cabinet knob, re-caulk a backsplash joint with a flexible sealant, and photograph a drawer slide to identify its type before calling. That’s diagnostic work, and it’s useful. Where DIY goes wrong is at the load-bearing and water-side parts: replacing a stripped hinge-plate in a cabinet gable, swapping undermount slides on a full bank of drawers, reseating a countertop seam, or opening a wall to trace a slow leak under the sink. Those go wrong quietly, and a mis-drilled cabinet face or a seam that fails after you’ve sealed it costs more to fix than the original problem did. Glendale homes with older cabinetry raise the stakes further, because the wood behind the screw hole may already be compromised. Call us at (844) 320-5930 and we’ll walk you through what you can check yourself and what needs a crew.
FAQs

Cabinet hardware typically runs 10 to 15 years under normal use, and countertop seams and backsplash joints often need attention sooner in Glendale because of the hot, dry summer cycling followed by winter rain. Lifespan comes down to load, moisture, and whether the substrate was sound at install. Call (844) 320-5930 for an exact quote, and estimates are free.
Sometimes yes. A single stripped hinge-plate can often be repaired with a hardwood insert or a conversion plate, and a failing drawer slide is a straightforward swap if the cabinet box is intact. Countertop seam failures and rotted sink-base panels usually call for replacement of the affected piece. We’ll tell you which one you’re looking at after a walk-through. Call (844) 320-5930 to book a free estimate.
A single hardware or slide replacement is a short visit, while a full cabinet run or countertop swap takes longer and depends on lead time for the matched material. We give you a written schedule with the written price so there are no surprises mid-job. Call (844) 320-5930 to schedule your free estimate.
We match by measurement and label rather than guessing from photos, pulling one door and one drawer to read hinge cup depth, slide type, door thickness, and any series label inside the box. From there we source OEM-compatible components or a vetted aftermarket equivalent, and you see the part line on the quote before we order. Call (844) 320-5930 and we’ll get the measurements started.
Whether you’re planning a full Glendale kitchen remodel or replacing a single failing drawer bank, the next step is the same: a written price and a written scope before any work begins. Rowan Construction Group Glendale brings up to 19 years of technician experience to each job, along with background-checked, uniformed technicians and a documented photo record on every visit, included as standard. Call (844) 320-5930 to schedule your free estimate.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












