







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Bathroom Remodeling: The Glendale Owner’s Guide
Bathroom remodeling that involves Tamko products in Glendale typically runs $9,000 to $28,000 installed, depending on whether you’re reworking a full bath or a smaller footprint, and we quote the flat written price before any work starts. We install and repair around Tamko materials as an independent contractor, not affiliated with the manufacturer. Most Glendale owners discover a failing component the same way: a discolored patch at the base of a shower wall, a tile that flexes underfoot, or a gasket that lets a thin line of water past the shower pan after every use.
Which Tamko Models This Applies To
Tamko’s footprint in a bathroom is narrower than its roofing line, and that matters for compatibility. Their waterproofing membranes, underlayments, and moisture barriers are specified by roll width, thickness in mils, and application (shower pan, wall, or floor), not by a single model number the way a faucet cartridge would be. The label on the roll and the printed spec sheet are your source of truth – not the color of the packaging, which has changed more than once. When you call, have the printed product code, the roll width you measured, and the substrate it’s bonded to (cement board, plywood, or existing tile) ready. If a Tamko roll isn’t available in the exact spec, we’ll show you a quality aftermarket equivalent side by side, with the spec sheet for each, and let you decide. We don’t claim to stock Tamko parts or carry them on a truck; any part is sourced to the job. For the fixtures and finish side, we work across KraftMaid, Cambria, and Silestone as well.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Bathroom Remodeling Is Failing
- Soft or spongy floor near the shower pan. Water is getting past the membrane seam, usually because the overlap was run the wrong direction and gravity carries moisture into the joint instead of away from it.
- Discoloration at the base of tile or wall panels. This is moisture trapped behind the barrier, which in Glendale’s warm inland summers often shows up faster than owners expect because the wall assembly stays warm and humid inside.
- Lifting or bubbling membrane edges. Adhesive failure, common where the substrate wasn’t primed or was dusty when the roll went down.
- Musty smell that returns after cleaning. The barrier is compromised and the cavity behind it is holding moisture. Cleaning the surface won’t fix it.
- Cracked or delaminated underlayment under tile. Movement in the subfloor has broken the bond, and the tile above it will fail next.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, a bathroom remodel in the $9,000 to $28,000 range reflects the materials chosen, the square footage, and how much of the existing assembly has to come out. A smaller bath or a targeted replacement at the waterproofing layer sits nearer the bottom of that band; a full re-tile with new membrane and fixtures sits nearer the top. The written quote is line-item, split between materials and labor, so you can see exactly what the Tamko-spec materials cost versus the install. Under Clause 1 of The Haven Standard, that price is fixed before anyone picks up a tool, and no change proceeds without a signed change order. The work carries our 365-Day Done Right Promise – if it’s not done right, we make it right.
DIY or Call Us?
You can safely check the obvious: measure the affected area, photograph the discoloration, look for the printed spec on the membrane roll, and note whether the floor feels soft underfoot. Where owners get into trouble is at the waterproofing layer itself – a membrane that’s cut, patched, or re-bonded without the right primer and overlap direction will leak again within a season, and by then the substrate behind it may need replacing too. That’s not a scare tactic; it’s the most common callback we see. If you’ve reached the point where water is getting in, call (844) 320-5930 and we’ll schedule a free estimate with a written price and a photo record of what we found.
FAQs

A properly installed membrane should hold for 20 to 30 years. In practice, most failures we see in Glendale come from installation error at the seams, not from the material aging out. Call (844) 320-5930 for a free estimate if yours is failing.
Sometimes. A single compromised seam or a small patch can be repaired if the surrounding membrane is intact and the substrate is dry. If moisture has reached the substrate, a patch won’t hold and replacement is the honest answer. We’ll tell you which it is after inspection.
A targeted repair can be a single visit. A full membrane replacement with re-tiling typically runs several days depending on the size of the bathroom and how much has to come out. The written scope gives you the expected timeline before work starts.
We match by the printed product code and measured spec, then confirm the substrate and application before ordering. If the exact Tamko spec isn’t available, we present a quality aftermarket equivalent with its spec sheet side by side. We don’t carry stock; every part is sourced to the job. Call (844) 320-5930 for a free estimate.
Ready for a written price on your Glendale bathroom project? Call (844) 320-5930 for a free estimate – we’ll bring the spec sheets, measure the substrate, and put the number in writing before any work starts.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












