







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Glendale Owner’s Guide
We install Schluter-compatible driveway and paver systems in Glendale, and the installed price for a paver driveway typically runs $7,000 to $18,000 depending on square footage, base prep, and drainage. Schluter’s exterior systems belong under tile and stone, not under standard interlocking pavers, so the first honest step is confirming which one you actually own before we quote a part. Most Glendale owners discover the problem the same way: a loose tile at the driveway apron, a dark damp line spreading from the garage slab, or a paver that rocks when the car rolls over it.
What usually started as one hairline crack turns out to be a failed uncoupling membrane, a clogged drainage mat, or a bond coat that never cured. In Glendale’s summer heat and winter rain, those failures travel fast.
Key Takeaways
- Schluter exterior systems (DITRA-DRAIN, KERDI-DRAIN, and their profiles) sit under tile and stone, not under every paver driveway. We confirm your system before pricing anything.
- Installed cost in Glendale runs $7,000 to $18,000 for a paver driveway and $250 to $700 for sealing.
- You get a written, itemized price before any work starts, a signed change order for any adjustment, and a documented photo record of what we found.
- We’re an independent contractor. Rowan Construction Group Glendale is not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Which Schluter Models This Applies To
Schluter’s exterior drainage and membrane family covers three situations that Glendale homeowners most often confuse. DITRA-DRAIN is a dimpled uncoupling membrane with a drainage mat built in, used under exterior tile and stone where water has to move sideways to a drain. KERDI-DRAIN covers the bonded waterproofing and drain assemblies at aprons and thresholds. And the profiles (DILEX, SCHIENE, TREP-E) finish edges, steps, and the transition between driveway and garage slab.
Identifying your system takes five minutes. Look at the substrate under the failed tile: a waffle-grid orange or grey mat means DITRA or DITRA-DRAIN; a felt-like sheet with a fabric fleece face means KERDI. Measure the tile or paver thickness and note whether the joint is grouted or open. If you’re matching a replacement, the profile height has to match the tile thickness within about 1 mm, or the edge sits proud and becomes a trip point.
OEM versus aftermarket for Schluter is a real decision. The membrane itself is a formed plastic sheet, and quality equivalents exist, but the fleece bonding layer and the dimple depth drive performance. On a driveway where cars load the tile, we specify the Schluter profile matched to the existing system rather than a generic edge strip. For pavers paired with these systems, we source through Belgard and Techo-Bloc for the surface and Schluter for the substrate and edging. We also work with KraftMaid, Cambria, and Silestone on the interior side, but that’s a different page.
Signs Your Schluter Driveway & Pavers Is Failing
- Hollow tile at the apron. Tap the tile near the garage door. A dull thud means the bond to the membrane has released, usually because moisture got under the font and froze or the thinset skin dried before the tile went down.
- A rocking paver near the drain line. When a paver moves underfoot, the bedding layer has washed out. In Glendale, the culprit is almost always a drainage mat that clogged with fines and pushed water sideways instead of down.
- Dark damp lines spreading from the slab edge. This is water sitting in the dimple layer with nowhere to go. The membrane is doing its job of keeping water out of the building, but the outlet is blocked.
- Efflorescence on the paver faces. White powder on the surface means salts are being drawn up through the base. It points to poor drainage and a base that never compacted properly.
- Ruts or settlement where the car parks. Uneven loading on a thin base compresses the granular layer. You’ll see it as a low spot the car always noses into, and it only gets worse with every rain.
Any of these can be repaired in isolation, but two or more together usually mean the whole assembly needs to come up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Glendale, replacing the Schluter exterior system under a tile apron and resetting the paver driveway runs $7,000 to $18,000 for a full paver driveway installation. Concrete driveway installation comes in at $4,500 to $12,000, and a straight driveway replacement runs $5,000 to $14,000. Sealing, if you want a fresh coat after the reset, adds $250 to $700.
What drives the range: square footage, depth of base removal, whether the drainage mat is continuous or in sections, and the profile count along edges and thresholds. Every quote is itemized by area and material, with the part priced separately from labor. Nothing gets ordered until you’ve seen the number in writing.
Our work carries the 365-Day Done Right Promise: if a replaced section lifts, rocks, or fails to drain within a year, we make it right. And you get a documented photo record of the substrate, the membrane, and the finished surface as part of every visit.
DIY or Call Us?

You can safely check three things yourself. Tap the tile for hollow spots, measure joint widths, and photograph the edge profile so you know your exact model. That’s reconnaissance, and it helps us price accurately.
What we don’t recommend doing yourself is pulling the tile and rebonding to a drainage membrane. The waterproofing layer, the drainage path, and the load transfer all sit in a few millimeters of space. A membrane that isn’t fully bedded, or a profile that sits 2 mm proud, can trip a pedestrian or channel water into your garage slab. The base and thinset under load-bearing driveway tile is the part most likely to fail when done by hand.
If you’ve found one hollow spot or one rocking paver, call us at (844) 320-5930. We’ll give you a written price and a second opinion on any estimate you already have.
FAQs
Fifteen to twenty-five years is realistic if the drainage mat stays clear and the base was compacted correctly at install. In Glendale, the two failure drivers are summer UV on exposed profiles and winter rain that carries fines into the drain layer. Clearing leaf litter from the drain outlet twice a year is the single easiest way to extend life. Call (844) 320-5930 for an exact quote on replacement.
Sometimes yes. A single loose tile can be pulled and rebonded if the membrane beneath it is intact and the drainage path is clear. Once you have two or more loose tiles in the same run, the repair rarely holds, and we’ll tell you that honestly. Call (844) 320-5930 and we’ll look at it before you commit to a full replacement.
A single apron reset is one to two days; a full driveway with base removal and drainage rerouting runs three to five days. Weather and permit lead times affect the schedule. Estimates are free, and we’ll give you the calendar window in writing.
We measure the profile height, the tile thickness, and the membrane dimple depth, then match to the exact Schluter series in your system. We don’t carry stock or keep parts on a truck; parts get ordered per job to your spec. That’s why the quote reflects the real part cost, not a marked-up guess.
If your driveway or apron is holding water, rocking underfoot, or showing white efflorescence, the fix starts with measuring the part, not guessing at it. Call Rowan Construction Group Glendale at (844) 320-5930 for a free written estimate and a documented photo record of what we find.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












