







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Glendale Owner’s Guide
Schluter bathroom remodeling in Glendale typically runs $9,000 to $28,000 installed, depending on tile area, whether we’re rebuilding a shower pan, and how much of the existing framing and plumbing we can keep. The bonded waterproofing system is what makes the difference: Schluter KERDI membrane, DITRA uncoupling mat, KERDI-BOARD panels and the matching drain and profile pieces work as one assembly, so a single failed part usually means water has been getting where it shouldn’t. Owners in Glendale call us most often after a loose tile sounds hollow underfoot, a shower pan drain shows a hairline crack at the flange, or grout along a curb keeps going dark no matter how many times it’s sealed.
Which Schluter Models This Apply To

Schluter isn’t one product, so matching the right part starts with identifying which line is already in your bathroom. The common ones we see in Glendale bathrooms are DITRA and DITRA-HEAT uncoupling mats under floor tile, KERDI and KERDI-BAND sheet membrane in showers, KERDI-BOARD foam backer panels for walls and benches, the KERDI-LINE linear drain and KERDI-DRAIN point drain assemblies, and the SCHIENE, JOLLY and RONDEC edge profiles that finish tile edges.
Identification is mostly measurement and labeling. DITRA and DITRA-HEAT come in 1/8 inch and 5/16 inch thicknesses, and the mat’s fleece side faces the substrate, so a scrap pulled from a failed floor tells you which you have. Drain assemblies are stamped on the flange with the series. KERDI-BOARD panels are printed along the edge with thickness (1/2, 5/8, 3/4, 1, 1 1/2 or 2 inch) and panel size. Write those numbers down before you call anyone, including us.
On OEM versus aftermarket: for the waterproofing membrane and drain flange, we specify Schluter-made parts, because the system’s warranty logic depends on matched components and mixing brands voids that logic. For edge profiles and trim, a quality aftermarket equivalent is a reasonable call when the sizing matches. We’ll tell you which is which in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Here’s what failure actually looks like, and why each symptom shows up:
- Hollow-sounding floor tile. The thinset has debonded from the DITRA mat, usually because the mat was installed with the wrong trowel notch or the fleece was contaminated with dust. It sounds like a drum when tapped.
- Grout that won’t stay sealed around the shower base. Water is moving behind the tile through a breached KERDI seam or a missed KERDI-BAND overlap at a corner. Re-sealing grout hides it for a month and then it returns.
- A hairline crack ringing the drain. The KERDI-DRAIN flange connection has separated, often from movement in the subfloor or a pan that was poured without the required mortar bed under the tray.
- Soft or crumbling drywall at the shower’s outside corner. Moisture has traveled past the membrane edge. This is common in Glendale’s older Spanish-revival bathrooms where the original framing wasn’t square and the panel joints were shimmed.
- Lippage at tile edges along a profile. The SCHIENE or JOLLY profile has lifted or the tile beneath it has moved, which points to substrate deflection rather than the trim itself.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A full Schluter-system bathroom remodel in Glendale runs $9,000 to $28,000. A smaller bathroom, typically under 40 square feet of floor, lands at $5,000 to $12,000. If the failure is isolated to a shower, a walk-in shower installation runs $4,500 to $12,000, a tub-to-shower conversion $3,500 to $10,000, and a shower replacement $3,000 to $8,500. A vanity swap on its own is $800 to $3,000.
What moves you within that range: total tile square footage, whether the pan is poured fresh or a tray is reused, the drain type (linear KERDI-LINE costs more than a point drain), and how much framing and plumbing has to be opened up once the membrane comes off. Every quote is a flat written price with a written scope and a written warranty before work starts, and materials are listed line by line so you see the membrane, drain, profiles and setting material separately from labor.
DIY or Call Us?
Some of this you can safely check yourself. Tap the floor tile with a coin and note where it sounds hollow. Look at the drain flange for cracks. Run a level across a shower curb. Take photos of the labels on any exposed membrane or panel edge. None of that involves opening a wall or cutting into a waterproofed assembly.
Where DIY goes wrong is at the membrane and the drain. KERDI seams have to overlap by a set amount with the correct thinset and a fully embedded bond, and the drain flange has to sit at the exact height the tray or mud bed requires. Get either wrong and the leak returns inside a season, often in a spot you can’t see until the ceiling below stains. There’s no electrical or gas danger in a Schluter system, but there is real risk of trapping moisture in wall cavities and framing, which is expensive to fix later. Call (844) 320-5930 and we’ll tell you honestly whether you’re looking at a repair or a rebuild.
FAQs

A properly installed Schluter assembly should last 25 years or more, and the membrane itself is the part that fails least often. What typically ends the system’s life in Glendale is heat cycling and slab movement in older homes, which stresses seams and drain connections long before the membrane wears out. If your shower is past 15 years and showing symptoms, call (844) 320-5930 for a free estimate rather than waiting for a ceiling stain.
Sometimes, yes. A localized breach at a corner or around a drain can be cut back, re-bonded with KERDI-BAND or KERDI-FIX, and re-tiled, provided the surrounding membrane tests sound. When moisture has spread more than a few square feet, a partial repair usually costs nearly as much as redoing the shower floor, so we’ll price both and show you the difference. Call (844) 320-5930 for an exact number.
A localized membrane repair is usually a two to three day job including cure time and re-tiling. A full shower rebuild with a fresh pan, KERDI-BOARD walls and new tile runs one to two weeks depending on tile size and dry time. We schedule around the rest of the house so your only working bathroom isn’t out of commission longer than it has to be.
We match the part to your identified series and thickness, then order through Schluter’s distribution channel, so you’re getting the OEM component rather than a substitution. Your written quote lists the exact part, size and quantity before anything is ordered. We also handle KraftMaid, Cambria and Silestone selections when a bathroom remodel includes the vanity and countertop. Call (844) 320-5930 to start with a free estimate.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












