







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
American Standard Kitchen Remodeling: The Glendale Owner’s Guide
American Standard kitchen remodeling in Glendale typically runs $14,000 – $45,000 installed, with small kitchens landing between $9,000 and $20,000. American Standard is best known for faucets and fixtures, not cabinets, countertops or full kitchen packages – so most Glendale homeowners in our experience are matching an American Standard faucet, sink or pull-down sprayer into a broader kitchen remodel rather than buying a branded store-bought kitchen. That mismatch is exactly where projects go sideways.
You usually spot the problem mid-planning, not mid-project. The old faucet drips at the base, the pull-down wand loses pressure, the undermount sink starts to flex, or you’re staring at an American Standard Rough-In Valve spec sheet wondering what the cabinet fabricator actually needs to know. Glendale kitchens in 1920s Spanish-revival homes and 1980s condo remodels both have specific plumbing wall layouts that change which American Standard model lines fit. More on that below.
Key Takeaways
- Installed kitchen remodel pricing in Glendale: $14,000 – $45,000; small kitchens $9,000 – $20,000.
- American Standard kitchen products are primarily faucets, sinks and valves – not full cabinetry.
- We’re an independent contractor. We are not affiliated with American Standard.
- Written flat price before any work starts. No change proceeds without a signed change order.
- Free second opinion on any written estimate, line by line.
Which American Standard Models This Applies To

American Standard’s kitchen lineup isn’t organized the way cabinet manufacturers organize theirs. There’s no “Series 200” family that maps cleanly to a remodel. Faucets fall under named collections (Berkley, Chatfield, Delancey, Fairbury, Portsmouth, Studio S), sinks are sold as undermount or drop-in by measured bowl size, and valves like the Flash Rough-In and the 3/8-inch compression rough carry their own part numbers on the valve body. Model numbers are stamped on the underside of the faucet base, inside the sink bowl apron, or on a sticker on the spray wand hose; a tape measure and a phone camera capture all three in under two minutes.
The compatibility gotcha in Glendale: Spanish-revival and pre-war kitchens here often use undersized 1.375-inch (1-3/8″) deck holes with non-standard centers. A standard American Standard 8-inch widespread or 4-inch centerset faucet will not drop in without a deck patch and re-drill – and re-drilling a porcelain or cast-iron sink means accepting the risk of a crack. Measure centers before you buy.
OEM vs. aftermarket on American Standard is a real decision. OEM cartridges and spray heads run higher but fit the exact casting; a quality aftermarket cartridge (typically half the price) is a reasonable call for high-turnover parts like spray wands, riskier for internal valve cartridges where tolerance matters. We quote both without pretending one is always better.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your American Standard Kitchen Remodeling Is Failing
- The base drips after every use. The cartridge or O-ring seat has worn past tolerance – typically a 6-to-9-year failure in Glendale’s hard water, faster than the general American Standard lifespan claims.
- The pull-down wand loses pressure but the base is fine. The diverter or spray head is the failure point, not the faucet body – a $20-$60 part in most cases, not a faucet swap.
- The undermount sink flexes or creaks. The American Standard sink clip or epoxy bond has separated from the countertop – a real risk falls a sink if left, so stop using it and get eyes on it.
- The valve handle catches or the water temperature surges. The rough-in valve’s balancing cartridge has scaled up – a repair, not a full replacement, if caught before mineral damage.
- Water stains on the cabinet interior below the sink. That’s a failing supply line or a failed sink seal, and it will destroy the cabinet base within weeks. Investigate that day.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for American Standard kitchen work in Glendale:
- Faucet swap (American Standard, same-footprint): typically $180 – $420 in labor, part extra.
- Full kitchen remodel: $14,000 – $45,000 (small: $9,000 – $20,000).
- Cabinet installation: $4,000 – $13,000.
- Countertop installation: $2,000 – $6,500.
- Backsplash: $800 – $2,500.
- Kitchen island: $3,000 – $10,000.
What drives the range: cabinet footprint and depth, whether the plumbing wall moves, countertop material, and whether the sink needs re-drilling. The written quote separates American Standard fixture cost from labor from cabinetry – you see the line items, not a bundle. Every job carries the 365-Day Done Right Promise, and every visit includes a documented photo record.
DIY or Call Us?
Safe to check yourself: shut off the under-sink supply valves, look for weeping at the base and supply fittings, snap a photo of the model sticker, and measure the deck hole and centers. All clean, no danger.
Where DIY goes wrong: pulling an American Standard cartridge on a valve body that’s 15+ years old often cracks the valve seat – and a cracked seat means a wall opening, not a part swap. Loosening a sink clip on a stone counter without knowing whether the counter bond is intact risks the sink dropping. Just stop, shut the valve off, and call us. A plumber’s camera visit is cheaper than a fallen sink or a flooded cabinet.
Call (844) 320-5930 for a free estimate and a written flat price before any work starts.
FAQs

How long does an American Standard kitchen faucet actually last in Glendale?
Roughly 8 – 12 years for the faucet body, with cartridges and spray wands failing closer to 5 – 9 years in Glendale’s hard water supply, which runs noticeably harder than most of LA County. Glendale Water & Power draws from a mix of state and local sources with high mineral content, and that shortens cartridge life versus the manufacturer’s generic claim. Call (844) 320-5930 if you want an honest read on your fixture.
Can my American Standard fixture be repaired instead of replaced?
Often yes – a cartridge or spray head swap fixes the vast majority of American Standard kitchen faucet failures. Repair only makes sense if the valve body and finish are sound; once the casting cracks or the chrome is peeling, replacement is the honest answer. We’ll tell you which you’re looking at on the first visit.
How long does the swap take?
A like-for-like American Standard faucet or spray head swap is typically a 1 – 2 hour visit. A sink replacement with a counter re-drill or cabinet work is a half-day and up. A full kitchen with American Standard fixtures runs the normal multi-week remodel timeline. Call (844) 320-5930 for a schedule tied to your specific scope.
How do you source the part?
Through our vetted brand network alongside KraftMaid cabinetry, Cambria and Silestone countertops, and Kohler and Toto fixtures – we quote OEM and quality aftermarket American Standard equivalents with part numbers in writing so you can verify. Nothing arrives without a documented price first.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












