







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Bathroom Remodeling: The Glendale Owner’s Guide
Wellborn bathroom remodeling in Glendale typically runs $9,000 to $28,000 for a full remodel, and a focused job like a vanity replacement or shower swap lands far lower in the contractor cabinet market, from about $800 for a vanity to $12,000 for a walk-in shower. We install and finish Wellborn-compatible bath packages across Glendale and quote a flat written price before any work starts, so you’re comparing a real number, not a ballpark. Rowan Construction Group Glendale is an independent contractor and is not affiliated with Wellborn.
Owners usually discover a problem in the finish sequence, not all at once. The vanity door starts catching on the frame after a Glendale summer, the shower wall panel lifts a corner behind the caulk line, or the medicine cabinet hinges loosen until the door hangs crooked. A bathroom remodel isn’t a single part that fails, it’s a chain of them: cabinet box, door and drawer hardware, countertop, shower surround, and the membrane behind it. Each has its own lifespan and its own failure signature. What matters is naming which link broke before you buy anything.
Key takeaways
- Full Wellborn bath package installed in Glendale: $9,000 – $28,000. Small bath: $5,000 – $12,000.
- Wellborn uses proprietary door and drawer hinge patterns; measure before ordering a replacement.
- The most common Glendale failure isn’t the cabinet, it’s the caulk and substrate behind it.
- We quote a flat written price and a written scope before work starts. Under Clause 1 of the Haven Standard, no work proceeds on a change until the change order is signed.
Which Wellborn Models This Applies To

Wellborn Cabinet builds its bath line in several collections, and the two that show up most in Glendale homes we work on are the inset and full-overlay framed door styles. The difference matters because the hinge placement and door thickness are not interchangeable. Inset doors sit inside the frame and use a butt hinge drilled into the stile; full-overlay doors cover the frame and use a concealed European-style cup hinge bored at a specific setback. Buy the wrong door for your box and it won’t close flush no matter how carefully you adjust it.
To identify what you have, pull one door and measure three things: the door thickness (typically ¾ inch on framed, ⅝ on some overlay styles), the cup bore diameter on the hinge (35 mm is the standard, but confirm), and the center-to-edge distance from the bore to the door edge. Write those down. That’s the info a parts person actually needs.
On OEM versus aftermarket: Wellborn-branded doors and drawer fronts are the only way to guarantee an exact stain and finish match to your existing cabinets. Aftermarket equivalents from a quality supplier can match the mechanics (hinges, slides, shelf pins, toe-kick clips) at a lower cost, but the color won’t match unless you’re repainting the whole run. In Glendale we generally recommend OEM for anything visible and aftermarket for concealed hardware. KraftMaid, Cambria, and Silestone come up here too, since a lot of Glendale bathrooms mix cabinetry brands in the same room, and matching a Cambria quartz edge profile to an existing counter is its own compatibility question.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Wellborn Bathroom Remodeling Is Failing
These are the symptoms we’re called out to Glendale bathrooms for most often. Each points to a specific cause, not a vague “it’s aging.”
- Vanity door dragging or rubbing the frame. Usually a hinge that’s lost its adjustment screw or a box that’s settled because the floor under it wasn’t level. In older Glendale homes with pier-and-beam subfloors, a cabinet can shift a quarter inch in a dry season and come back in the wet one.
- Soft or spongy floor near the toilet or shower. Water has reached the subfloor. The cabinet isn’t the problem; the waterproofing failed first, and the cabinet is the messenger. Don’t replace the vanity until the source is found.
- Shower wall panel lifting at a corner or seam. The caulk behind it failed, or the panel was installed over a wet substrate. Once water gets behind a surround panel, the panel itself is usually a loss; the question is how far the damage spread.
- Drawer slide grinding or catching. Glendale’s dry summers and Santa Ana wind events pull moisture out of wood, and a drawer box can rack slightly out of square. Usually a slide replacement fixes it; sometimes the box needs re-squaring.
- Countertop seam opening or a chip at the edge. Movement in the cabinet run, or an undermount sink that’s pulling away from its adhesive. Quartz chips cleanly and can often be repaired; a lifting sink usually needs to come out and reset.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Wellborn-compatible bathroom work runs in Glendale, itemized. These are installed prices (materials plus labor), not cabinet-only.
| Scope | Installed price range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
What drives the range: the size of the room, whether the subfloor or waterproofing needs repair, whether the layout is changing (moving plumbing adds cost fast), and the finish level. A single-vanity swap in a smaller Glendale condo sits near the bottom; a full gut with a custom walk-in shower and new tile floor sits near the top. You get a flat written price with a written scope and a written warranty before any work starts, and the work carries our 365-Day Done Right Promise. If a change comes up mid-job, nothing proceeds until you sign the change order.
DIY or Call Us?
You can safely do the inspection. Pull a door, photograph the hinge, measure the bore and setback, check the caulk lines for gaps, and feel the floor near the shower for softness. That’s diagnosis, and it saves time on the call.
Where DIY goes wrong: waterproofing. We see more failed Glendale bathroom jobs from a shower surround installed over drywall or a pan liner that wasn’t sloped than from any cabinet defect. Once water is behind a wall, the repair is a demolition, not a swap. If you’re swapping a vanity or replacing hardware, that’s within reach for a careful homeowner. If you’re opening a shower wall or touching plumbing, have it done right the first time.
We install Wellborn-compatible packages plus KraftMaid cabinetry, Cambria and Silestone counters, and the fixtures that go with them. Call (844) 320-5930 for a free estimate, and bring any other written quote you have; our free second opinion walks it line by line, no charge.
FAQs

How long does a Wellborn bathroom cabinet last in Glendale? A well-made cabinet box lasts 20 to 30 years; the finish and hardware are what give out first, typically at 10 to 15. Glendale’s dry summers dry out wood and its wet winters swell it, so doors and slides take more wear here than in a steady-humidity climate. Hardware replacement usually buys several more years before a full remodel. Call (844) 320-5930 for an exact quote, and the estimate is free.
Can a failing vanity or shower be repaired instead of replaced? Often yes. Hinges, slides, caulk joints, and a lifting panel can be repaired without a full replacement if the substrate is dry and intact. Once the subfloor is soft or water is behind a wall, repair becomes a patch over a bigger problem and a proper replacement is the honest answer. Call (844) 320-5930 and we’ll tell you which one you’re looking at, free.
How long does the swap take? A vanity swap is usually a single-day job once the part is in hand. A shower replacement runs three to five days depending on tile and waterproofing. A full bathroom remodel in Glendale runs one to three weeks. The exact part and the condition of what’s behind it set the schedule. Call (844) 320-5930 for a written scope and timeline.
How do you source the Wellborn part? We match OEM Wellborn doors, drawer fronts, and hardware for a color and fit match, and use quality aftermarket equivalents for concealed hardware when that’s the cost-honest choice. We don’t claim to stock parts or carry them on a truck. We order against your measurements and let you know the lead time in writing before we start. Call (844) 320-5930 for a free estimate.
Written by the team at Rowan Construction Group Glendale, serving Glendale and nearby areas.












